12
EN
Thank you for choosing the Qubo
01_GENERAL SAFETY WARNINGS
Before using your trainer, carefully read the
warnings listed below for your health and
safety.
1. The appliance is not to be used by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction.
2. Children being supervised not to play
with the appliance.
3. Before beginning a training programme,
undergo a physical examination certifying
good health.
4. Choose a training level compatible with
your physical endurance and the status of
your health.
5. If you feel particularly fatigued or sore
while exercising, stop using the trainer
immediately and consult your doctor.
The above warnings are general and not
exhaustive of all the precautions that should
be taken for the proper and safe use of the
trainer; which is solely the responsibility of
the user.
02_PRODUCT MODIFICATIONS
Also in view of any technical update, ELITE reserves
the right to make changes to the products or their
specifications without being obliged to notify or inform the
Customer beforehand for:
a) changes that do not affect negatively the product
performance;
b) changes required to meet or improve the product
specifications;
c) changes necessary for the products to comply with the
applicable legal requirements.
ELITE also reserves the right to supply these products
with these improvements without being obliged to or
responsible for applying the same modifications to any
previously purchased products, reserving also the right to
change prices and model availability according to market
conditions, component availability and other corporate
considerations.
03_DISCLAIMER
Elite S.r.l. is not liable for any temporary or permanent
damage to the physical integrity of the user, whether direct
or indirect, resulting from the use of the trainer.
04_NOMBRE Y ELENCO DE LOS
COMPONENTES
Check the presence of all the following components:
N°1 Qubo frame
(Ref. A)
N°1 Unit
(Ref. B)
N°1 Quick release
(Ref. C)
N°2 M6 Unit screws
(Ref. D)
N°10 Levelling (equalizing) feet
(Ref. E)
ATTENTION
Resistance unit depicted here may vary from
production models
05_UNIT ASSEMBLY
- Unfold the frame (A) from its packaged position (Pic. 1)
and place it on a flat surface (Pic. 2)
- There are 2 pairs of holes on its base to be used with
different roller diameter options:
1) Use the front pair of holes for a 30mm diameter roller
unit (Pic. 3);
2) Use the rear pair of holes for a 45mm diameter roller
unit (Pic. 4);
- Tighten the M6 screws (D) (Pic. 5 and Pic. 6) completely,
utilizing the correct holes for the different roller diameter
options.
- Use solely the included wrench to attach the resistance
unit to the frame base as shown in the figure. Tighten ¼ of
a turn after contact is made between resistance unit and
frame base (apply max force 2 Nm) (Pic. 7).
06_FITTING THE BICYCLE
- Make sure the quick release of the bicycle rear wheel is
properly fixed.
- Turn the lever (F) to the “open” position (Pic. 8).
- Put the bicycle in position, inserting the left end of the
rear quick release in the left bushing (Pic. 9). For safer
clamping of the bicycle on the stand, make sure the lever
of the quick release is horizontal (Pic. 10).
Summary of Contents for QUBO
