13
EN
- Close the lever (F), making sure it starts pressing the
quick release inside the predefined work
area; between 55° and 65° (Pic. 11).
- If the lever (F) starts pressing the quick release in the
advanced work position (Pic. 12), screw the
left bushing pin (g) (Pic. 13) so that the lever (F) starts
working inside the predefined work area (between 55° and
65°) (Pic. 11).
- If the lever (F) starts pressing the quick release in the
delayed work position (Pic. 14), unscrew the left bushing
pin (G) (Pic. 15) so that the lever starts working inside the
predefined work area (between 55° and 65°) (Pic. 11).
- If the bicycle wheel sets up too far from the centre of the
roller (Pic. 16), loosen the resistance unit (B) attachment
bolts (D), slide the resistance unit left or right as necessary,
and re-tighten the bolts (Pic.17, Pic.18 and Pic.19).
- Push the bicycle towards the resistance unit until the rear
wheel touches the roller (Pic. 20).
- Verify the stability of the bike by pushing and pulling the
horizontal tube of the frame and the saddle. Should the
bike still not appear stable, make sure its quick release and
lever are correctly positioned, that the lever (F) is in a
“closed” position and the adjusting of the clamping system
has been carried out correctly.
07_BIKE REMOVAL
- Hold the bicycle with one hand and with the other open
the lever (F), turning it to the “open” position (Pic. 21).
Remove the bicycle.
- For carrying, or storage, it is advisable to close the stand.
(Pic.22 e Pic.23).
- In order to further reduce the storage footprint remove
the unit (B) from the frame (A) and place it back in its
original packaging and fold the frame as indicated in Pic.
24 and Pic. 25.
08_LEVELLING FEET ASSEMBLY
- The Qubo frame (A) comes equipped with levelling feet (E)
to compensate for uneven surfaces that do not allow the
four feet to make complete contact, and to allow the bike
to be perfectly vertical (Pic. 26).
- The levelling feet (E) can be mounted under the front feet
(Pic. 267 and Pic. 28).
- The levelling feet (E) can be mounted under the rear feet
(Pic. 29 and Pic. 30).
- If a single levelling foot (E) isn’t sufficient, it is possible
to add additional feet to those already mounted. (Pic. 31,
Pic. 32, Pic. 33 and Pic. 34).
Warning: the direction of the foot (E) is turned 90° in
relation to the first one positioned.
09_ATTENTION
- Keep people, children and animals away from the roller
during use, since the moving and rota- ting parts of the
roller and the bicycle can cause damage in case of contact.
- Before starting training, position the trainer in a dry place,
away from potentially hazardous objects (furniture, tables,
chairs, etc.) in order to avoid any risk of inadvertent or
accidental contact with them.
- The stand is designed for use by just one cyclist. - Check
the safety and stability of the bicycle before every training
session.
- If the quick release is not compatible with the bushings
of the stand, replace it with the one supplied (C).
- There are no individually usable components on the
inside.
- Since the feet are made from soft non-slip material,
during use they may leave rubber marks on the floor.
- Detach the unit from the stand before moving the
hometrainer to avoid risk of damaging the system.
10_ADVICE ON USE
- For less tyre wear and better grip on the roller, it is
advisable to use tyres of 23 mm width.
- Recommended rear wheel pressure: 7 -8 atmospheres
for racing tyres; 3.5 - 4 atmospheres for MTB tyres. For
particular cases, comply with the pressure recommended
by the tyre manufac- turer.
- For quieter use, better grip of the tyre on the roller and
reduced vibration, use slick tyres (also for Mountain bikes).
- Before use, clean the tyre with alcohol or water.
- If the pin of the quick release supplied protrudes more
than 3 mm from the fixing nut, cut off the protruding part
(Pic. 35).
11_PACKAGING
If the roller needs to be shipped, careful packaging is
critical:
- pack up the Qubo in its original box.
Concerning shipments, packages often undergo strong
shocks and bumps, so any non-original packaging might
irreparably damage the home trainer. Such damages are not
covered by the warranty.
Note: before shipping the home trainer or any of its
components to customer service, constult Elite or its
distributor or your own retailer.
Any non-planned shipment might not be accepted.
Technical assistance:
Phone +39 049 5940044
e-mail: [email protected]
Summary of Contents for QUBO
