Elite Fuoripista, Instructions Manual

Page: 21 / 63

21
EN
FUORIPISTA is an electronic device used to conduct
workouts to be interfaced with a personal computer or
mobile devices (iOS and Android) or with cycle computers
with ANT+™ and/or Bluetooth Smart technology, but also
to workout on its own with no devices other than the built-
in screen.
FUORIPISTA is compatible with most apps/software such
as: My E-Training, Zwift, TrainerRoad, The Sufferfest, some
Garmin Edge, RGT Cycling and many more.
My E-Training is an Elite-developed app compatible with
Windows and Mac computers (iOS and Android) that offers
many workout modes. Workouts are power or gradient-
based; there are videocourses, courses based on Google
Maps, you can import GPS data from your outdoor ride,
conduct evaluation tests and much more.
A "Stand-Alone" mode, which activates automatically if
FUORIPISTA isn't connected to a device or PC, is available,
so interactivity is ensured under any circumstance.
In this mode you can adjust the braking unit resistance
with the virtual gear shifter levers. Please check chapter
11_VIRTUAL GEAR SHIFTER for more info on the "Stand-
Alone" mode.
04_COMPONENTS LIST
Your FUORIPISTA includes the following components:
1 Interactive stationary bike
Ref. A
4 Feet Ref. B
Tablet terminal holder Ref. C
1 Handlebar tightening knob Ref. D
2 Side magnetic caps Ref. E
1 5mm hex key Ref. F
1 Power supply Ref. G
1 Seatpost adjustment wrench Ref. Q
3 Felt Ref. W
05_FUORIPISTA ASSEMBLY
- Cut the plastic fixing bands (Pic. 1);
- remove FUORIPISTA (Ref. A) from its supporting pallet;
WARNING: handle with care as the Fuoripista is quite heavy
(70 kg) and delicate (glass legs); please get at least one
other person to help you during this phase.
- select the area where to install FUORIPISTA and install its
4 feet (Ref. B) under the glass legs (Pic. 2)
- Rotate the handlebar (Ref. H) forward and slide it along
the rail, make sure that the interior rail is properly coupled
so the handlebar can be adjusted (Pics. 3-4-5-6).
- Assemble the handlebar tightening knob (Ref. D) and
make sure not to drop it on the glass flywheel (Pic. 7).
- Assemble the tablet terminal holder (Ref. C) by inserting it
in its proper front compartments (Pic. 8).
- Assemble the side magnetic caps (Ref. E) on the front
legs in correspondence of the edges of the flywheel shaft
(Pic. 9).
- Remove the lower cap (Ref. U) under the rear beam and
push the main switch (Ref. K) (Pic. 10). FUORIPISTA has
been designed to always be powered up so you don't need
to operate the main switch in-between workouts.
- Put the lower cap (Ref. U) back.
06_ADJUSTMENTS AND CYCLING SETUP
FUORIPISTA has been designed with a race bicycle setup in
mind; by adjusting the handlebar and saddle you can cover
frame sizes from small to XXL, so the user will be able to
adjust the setup according to his/her requirements.
07_HANDLEBAR ADJUSTMENT
You can adjust FUORIPISTA handlebar vertically: unscrew
the front knob (Ref. D) by holding it with two hands (Pic. 11)
and rotating it three times - make sure not to completely
untighten it.
Move the bar-ends (Ref. H) to the desired position (Pic. 12).
Lock the knob in place by holding it with 2 hands (Pic. 13).
WARNING: Do not completely untighten the knob (Ref. D)
so it doesn't drop on the glass below.
08_SADDLE ADJUSTMENT
FUORIPISTA saddle can be adjusted. To move it back,
forward or to tilt it, untighten the seatpost nut (Pic. 14) with
the 5 mm hex key (Ref. F), then adjust the position (Pic.
15) .
09_SEATPOST ADJUSTMENT
FUORIPISTA seatpost (Ref. Y) height can be adjusted. Get
the proper wrench (Ref. Q)(Pic. 16).
Insert its edge in the pin hole as shown (Pic. 17)
Unscrew counter-clockwise by half a turn (Pic. 18)
Adjust the seatpost (Ref. Y) height (Pic. 19), pay attention
not to rotate the seat tube, just change its height and
tighten the nut back.
ATTENTION: A rotation of the tube can ruin the surface of
the seat tube.
Fix the pin by tightening it clockwise as much as you had
untightened it.
Put the adjustment wrench back in its slot.
10_EMERGENCY AND POWER BUTTON
There's a button (Ref. P) on the front of FUORIPISTA, right
below the display (Pic. 20);
This button has 2 functions: power and emergency
brake. If it's in energy saving mode, the button powers up
FUORIPISTA so it's ready for use.
Conversely, on workouts it activates the emergency brake,