Programming additional transmitters
Operating procedure
Result
3
On the
(additional) trans-
mitter to be programmed,
press the [
UP
▲] button im
-
mediately (within 1 second)
after the blind starts moving
upwards.
The status display
lights briefly. The blind
stops briefly, starts
moving again and then
moves downwards.
4
On the (additional)
transmit-
ter to be programmed,
press
the [
DOWN/CLOSE
▼]
button immediately (within
1 second) after the blind
starts moving downwards.
The status display
lights briefly. The drive
will stop.
The additional transmitter is programmed.
Stop the bidirectional radio programming mode:
Hold down the [
STOP ■
] button for at least 6 seconds until
the status display lights up (depends on transmitter).
6.3 Deleting the radio connection between
transmitters and receivers
Refer to the respective instructions for the transmitter.
6.4 Programming or deleting further blind
positions
• Intermediate position: Blind at any position between
upper and lower end position.
Defining the
interim position
in the receiver
Approaching
the intermedi-
ate position
Deleting the
intermediate
position
Prerequisite: The blind
is in the upper end
position.
1. Press the [
DOWN/
CLOSE
▼] button
until the required
intermediate position
is reached.
2. Then press the
[
STOP
■
] button
. The
blind will stop. The
status LED lights up
briefly.
The intermediate posi-
tion is now stored.
Prerequisite: The
intermediate position is
defined.
• Double click the
[
DOWN/CLOSE
▼]
button
(twice in quick
succession):
Blind moves to the
saved intermediate
position.
If no intermediate posi-
tion has been defined,
the blind moves to the
lower end position.
If an intermediate
position is to be
controlled for several
receivers simultane-
ously, the receivers
must be programmed
on one channel (single
channel).
• Simultaneously press
and hold the [
DOWN/
CLOSE
▼] +
[
STOP
■]
buttons for
approx. 3 seconds.
The intermediate
position is now deleted.
The status LED lights
up briefly.
• Ventilation position:
Ventilation gaps for application of the roller shutters open
Defining the
ventilation
position in the
receiver
Approaching
the ventilation
position
Deleting the
ventilation
position
Requirement:
Blind is in the lower
end position.
1. Press the [
UP
▲]
button until the venti-
lation gaps open.
2. Then press the
[
STOP
■
] button
.
The blind stops. The
position of the ventila-
tion is now saved.
Prequisite:
Ventilation posi tion is
defined.
• Double click on the
[
UP
▲] button:
The blind travels
upwards to the saved
position.
If no ventilation position
is defined, the blind
moves to the upper
end position.
• Simultaneously
press and hold the
[
UP
▲]+[
STOP
■
]
buttons for approx
3 seconds.
The position of the ven-
tilation is now deleted.
Approach to the intermediate position and the ventilation posi-
tion takes place in the quiet mode travel profile (see section 7).
6 | EN
©
elero
GmbH
Relief function | End position adjustment
Changing/deleting the end positions
1
Switch on mains
2
Use the assembly cable to bring the blind to a central
position.
3
Press both direction keys [
UP
▲]+[
DOWN/CLOSE
▼]
simultaneously.
The drive travels up and down briefly for approx.
5 seconds.
The end position settings have been deleted.
The end positions are configured again automatically as
described in section 5.4.4.
6
Programming the transmitter
Important
Precondition: The drive must be in radio operation mode.
►
If the end positions have not been programmed, remove
the blind from the winding shaft.
6.1
Programming the first transmitter
Programming the (first) transmitter
Operating procedure
Result
1
Switch the power off and
on again
The drive is in learning
mode for approximate-
ly 5 minutes.
2
Press the programming but-
ton [
P
] on the transmitter to
be programmed for approxi-
mately 1 second.
The status display
lights up. The drive is
now in learning mode
(up/down travel) for
approximately
2 minutes.
3
Immediately (maximum 1
second) after the start of
upward travel, press the
[
UP
▲] button.
The status display
lights briefly. The blind
stops briefly, starts
moving again and then
moves downwards.
4
Immediately (maximum 1
second) after the start of
downward travel, press the
[
DOWN/CLOSE
▼] button.
The status display
lights briefly. The drive
will stop.
The (first) transmitter is now programmed.
6.2 Programming additional transmitters
Up to 16 transmitters can be programmed.
Programming additional transmitters
Operating procedure
Result
1
On an
already programmed
transmitter,
hold down
the buttons [
UP
▲]+
[
DOWN/CLOSE
▼]+[
P
]
(programming button)
simultaneously for
approximately 3 seconds.
The status display
lights up.
The drive is in learning
mode for approximate-
ly 5 minutes.
(alternative to the previous
line)
Switch the power off and
on again
The drive is in learning
mode for approximate-
ly 5 minutes.
2
On the
(additional) trans-
mitter to be programmed,
press the programming
button [
P
].
The status display lights
briefly. The drive is in
learning mode (up/
down travel) for approx-
imately 2 minutes.
