background image

DRY LOCATION

97+

HIGH CRI

DIMMABLE

24VDC

GOLD PLATED PCB

SINGLE SDCM

HIGH R9 & RF SKIN

SPEC LOCK

INSTALLATION GUIDE 

|

 DIM-TO-WARM LED TAPE LIGHT 

|

 IG090519-1.0 

|

 1 OF 5

INSTALLATION GUIDE

CELESTE DIM-TO-WARM LINEAR LIGHTING

SAFETY & WARNINGS

DO NOT CONNECT DIRECTLY TO HIGH VOLTAGE POWER!

Read all warnings and installation instructions thoroughly.

WARNING

DO NOT CONNECT DIRECTLY TO HIGH VOLTAGE POWER!

Read all warnings and installation instructions thoroughly.

WARNING

WARNING!

DO NOT CONNECT DIRECTLY TO LINE 

VOLTAGE POWER!

Read all warnings and installation instructions 

thoroughly.

HANDLE PRODUCT WITH CARE!

DO NOT

 BEND LED STRIP 

LIGHT TO A DIAMETER LESS 

THAN 

4 INCHES

.

4 in.

DO NOT 

BEND LED STRIP LIGHT 

ON A HORIZONTAL PLANE.

DO NOT

 COVER STRIP LIGHT WITH 

ANY MATERIALS.

DO NOT 

FOLD, CREASE, OR 

TWIST LED STRIP LIGHT.

DO NOT 

POWER STRIP 

LIGHT WHILE ATTACHED TO 

SPOOL OR TIGHTLY COILED.

1. Install in accordance with national and local electrical 

code regulations. 

2. This product is intended to be installed and serviced by 

a qualified, licensed electrician.

3. Do not modify or disassemble this product beyond 

instructions or the warranty will be void.

4. 

Do not submerge, or install within 5 feet of a swimming 

pool. 

5. 

All plastics are affected by the elements and may shift 

in color and other properties after product installation, 
particularly  with  direct  exposure  to  sun,  chlorinated 
water, and other chemicals.

6. Only install with a Listed Class 2 DC LED driver. 
7. 

To  avoid  Voltage  Drop,  ensure  wire  gauge  used  with 
LED Strip Light is sufficient. Refer to Voltage Drop Chart.

8. Do not exceed maximum run recommended for Strip 

Light.

9. CELESTE

 LED Strip Light is designed to be cut at 

designated cut points only. Cutting anywhere other than 
the cut points will result in damage to the Strip Light.

10. 

Failure  to  follow  safety  warnings,  and  installation 

instructions will void the warranty for this product.

POWER SUPPLY

CLASS

2

+ 24V

+ 24V

-

-

W

W

W

W

W

W

C

C

C

C

C

C

+ 24V

+ 24V

-

-

W

W

W

W

W

W

C

C

C

C

C

C

+ 24V

+ 24V

-

-

W

W

W

W

W

W

C

C

C

C

C

C

+ 24V

+ 24V

-

-

W

W

W

W

W

W

C

C

C

C

C

C

Summary of Contents for LUCETTA CELESTE






Reviews: