Elem Garden Technic TDE40V37-LI2BF, Translation Of The Original Instructions

Page: 44 / 58

OVERVIEW
1 Upper bar
2 Tightening levers for fastening
the upper bar
3 Lower bar
4 Impact protection
5 Tightening levers for fastening the lower bar
6 Carrying handle
7 Lever for cutting height adjustment
8 Cover
9 Rechargeable batteries
9a Release button on rechargeable battery
10 Ignition key
11 Wheels
12 Appliance housing
13 Grass collection box
13a Plastic tabs
13b Grass collection box rods
13c Handle for grass collection box
14 Cable holder
15 Machine cable
16 Release button
17 Start handle
18 Mulch kit
18a Bracket on mulch kit
19 Double charger
20 Blade
21 Blade bolt
22 Motor spindle
ASSEMBLY
• Only carry out work that you know you
are capable of.
• If in doubt, consult an expert or our
service centre directly.: sav@eco-repa.com
Mounting the lower bar (B)
1. Fold the lower bar (3) upwards.
2. Turn the lower tightening levers (5)
clockwise to fasten.
3. Lock the tightening levers (5) by pressing them
in the direction of the lower bar (3). The tightening
levers must be pulled tight and then positioned
against the bar so that tightening can be carried out
with medium force. If
this fails, continue to turn the tightening lever
clockwise, or loosen it by turning counter clockwise.
Mounting the upper bar (C)
. Fasten the upper bar (1) with the enclosed
screws (2b), the washers (2a) and the upper
tightening levers (2) on the right and left of the lower
bar (3).
The release button (16) must be located on the right
in the mowing direction. Two positions are possible.
2. Turn the tightening levers (2) clockwise
to fasten.
3. Lock the tightening levers (2) by pressing them
in the direction of the bar (3).
The tightening levers must rest against the bar in
such a way that tightening can be carried out with
medium force.
If this fails, continue to turn the tightening lever
clockwise, or loosen it by turning counter clockwise
Release the tightening levers (2+5)
and fold the upper bar (1) and the
lower bar (3) together so that the
device takes up less space. Make
sure not to pinch the machine
cables while doing this.
Mounting the (D)
1. Clip the handle (13c) of the grass collection box
(13) into the upper side of the grass collection box
(13).
2. Place the plastic tabs (13a) of the grass
collection box (13) over the grass collection box
rods (13b).
Mulch kit (J)
Attaching the mulch kit
1. Remove the grass collection box, if used.
2. Lift the impact protection.
3. Slide the mulch kit (18) into place. The bracket
(18a) snaps into place.
Removing the mulch kit
4. Push in the bracket (18a) on the mulch
kit and remove the mulch kit (18).
OPERATION
The device must only be
adjusted when the motor is
switched off and the blade is
stationary. There is a risk of
personal injury.
Switch off the apparatus,
remove the ignition key (10)
and wait for the blades to
come to a standstill.
Mounting/removing the grass collection box (E)
1. To mount the grass collection box (13), lift the
impact protection (4) and suspend the grass
collection box (13) from both receptors.
2. Fold the impact protection (4) over the grass
collection box (13). This will hold the grass collection
box in the correct position.
3. To remove the grass collection box (13), lift the
impact protection (4) and remove the grass
collection box (13).
Fold the impact protection (4) back over the device
housing (12).
Work may not be carried out
using the device without the
impact protection or grass
collection box. There is a risk
of injury.