Electrolux Combi TOUCH Series Page 4 User Manual Download | Manualshive

Page: 4 / 68

background image

4

A

WARNING AND SAFETY INFORMATION

A.1

General information

To ensure safe use of the machine and a proper understanding of the manual it is necessary to
be familiar with the terms and typographical conventions used in the documentation. The
following symbols are used in the manual to indicate and identify the various types of hazards:

WARNING

Danger for the health and safety of operators.

WARNING

Danger of electrocution - dangerous voltage.

CAUTION

Risk of damage to the machine or the product.

IMPORTANT

Important instructions or information on the product

Read the instructions before using the appliance

Clarifications and explanations

WARNING

Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating
and maintenance instructions thoroughly before installing or servicing
this equipment.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other appliance.

IMPORTANT

After installation put in a prominent location suitable instructions to be followed
in the event gas is smelt. This information shall be obtained by consulting the
local gas supplier.

• This appliance is to be intended for commercial and collective use, not for continuous mass

production of food nor for household use. Any other use is deemed improper.

• Only specialised personnel are authorised to operate on the machine.
• This appliance must not be used by minors and adults with limited physical, sensory or

mental abilities or without adequate experience and knowledge regarding its use.

«
...
2
3
4
5
6
...
»

Summary of Contents for Combi TOUCH Series





































































Reviews:

No comments

Related manuals for Combi TOUCH Series

Brand: PALSON Pages: 29

Brand: Franke Pages: 15

Brand: Galanz Pages: 12

Brand: CDA Pages: 12

Brand: Insignia Pages: 21

Brand: Hotpoint Pages: 16

Brand: Convotherm Pages: 34

Brand: Taurus Pages: 32

B64CS71 0B Series

Brand: NEFF Pages: 44

Brand: Gaggenau Pages: 60

Brand: Daewoo Pages: 30

Brand: Pelgrim Pages: 74

Brand: NEFF Pages: 140

Brand: Fagor Pages: 82

Brand: Panasonic Pages: 70

Brand: Panasonic Pages: 37

Brand: Bosch Pages: 48

Brand: Bosch Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands