background image

 54

5954 006 00

GB

IMPORTANT -1
Carefully rinse the inside of the generator with a rubber hose 
inserted through the generator access pipe, to remove all 
traces of descaler.

• Re

fi

 t the cap and close the steam generator drain (pushbutton 

or lever).

After these procedures it is advisable to operate the oven empty, 

in STEAM cycle, for 30 minutes.

IMPORTANT - 2
If the water cock is not easily accessible, to empty the boiler 
proceed as follows:

1) Open the boiler drain valve with the special pushbutton.

2) Wait 2 minutes and switch the oven off; the drain valve will 

automatically close. 

6.2 REPLACING CONSUMABLE COMPONENTS

Replacing the oven compartment lamp 

(Fig. 3)

To replace the oven compartment lamp, if burnt out, proceed as 

follows:

• Disconnect the power to the appliance.

• Undo the 4 screws 

fi

 xing the light 

fi

 tting ring nut "A" and remove 

the glass "V" together with seal "G".

• Remove the halogen lamp "L" and replace it with another one 

having the same characteristics (12V - 10W - 300°C), using a 

clean cloth or paper to avoid direct contact with 

fi

 ngers.

• Re

fi

 t the protection glass, correctly inserted inside the seal, in 

the lamp compartment and 

fi

 x the ring nut by retightening the 4 

screws, after smearing the seal with food-grade silicone grease.

  

      3

   

      

Replacing door seals 

(Fig. 4)

NB

: The door seal is a component that can become worn over 

time. It is advisable to replace it whenever any hardening or 

breakage is noticed.

To replace it, proceed as follows:

• Remove the seal from its seat and clean the latter of any traces 

of silicone.

• Apply a bead of silicone sealant at point 

1

 along the inside pro

fi

 le 

of the seal seat.

• Insert the new seal along the entire seat.

     

   4

 

6.3 PARTICULAR CLEANING

Discharge system cleaning and effi ciency check

 

Periodically clean the drain pipe, checking for any obstructions 

involving the draining of water.

Cleaning the door internal glass

 (Fig. 5)

These operations must be donet with the door glass cold, without 

using abrasive detergents or rags.

The interspace surfaces are accessed by opening the internal 

glass hinged on the door.

• With the door open, press the two top and bottom retaining clips 

F

 and open the internal glass.

                    

  

      5

   

      

After cleaning, close the internal glass against the rubbers.

Cleaning the CLEANING SYSTEM

 rotating jet (Fig. 6)

It is advisable to clean the jet in case of:

- long periods of CLEANING SYSTEM disuse

- dif

fi

 culty in wash arm rotation (probable nozzle obstruction)

- use of very hard water.
If the nozzles are completely obstructed, use the tip of a knife to 

remove any encrustations. 
• Extract (without removing) the retaining clip 

A

 from the middle 

block of the jet. For this operation insert the tip of a screwdriver 

in the part indicated by the arrow and turn it from the vertical to 

the horizontal position as shown in the 

fi

 gure.

• Remove the jet from the rotation pin.

 

 

       

      6

   

      

• Place the rotating jet in a bowl containing descaler, leave over 

night then rinse with plenty of water. 

•  Re

fi

 t the jet, inserting it on the rotation pin and pressing the 

retaining clip into its original position. 

Summary of Contents for 237033

























Reviews: