Electrolux 237033 Installation And Operator'S Manual Download Page 23

 53

5958 962 00

GB

5954 006 00

If required, 

completely

 

 remove

 suction wall:

- unscrew (2) nut C1 with a hexagon wrench.

- lift (3) the suction wall and remove it (4) from the bottom pin C 

of the oven compartment;

- lower (5) the wall to release it from the top pin D and completely 

remove it (6).

B2

B

D

C

C1

2

3

4

5

6

A

B2

1b

1a

B1

B1

  

      2

   

      

To re

fi

 t the wall, repeat the steps in reverse order and retighten 

nut C1.

• If present, clean the oven compartment 

grease fi lter 

(not sup-

plied) at least every three cooking cycles. 

• If present, clean the 

air  fi lter 

(not supplied)

 

at least once a 

month, removing it from under the 

control panel

Non-compliance with the above will result in 

fi

 lter inef

fi

 ciency and 

produce anomalous effects in cooking.
• Clean the stainless steel parts every day using lukewarm soapy 

water, rinsing with plenty of water and drying thoroughly.

• Do not clean the stainless steel with steel wool, brushes or 

scrapers in common steel, as they could deposit ferrous particles 

which oxidise, causing rust spots. 

• Whenever the appliance is not used for long periods:

- Disconnect the power supply and close the water;

- go over all steel surfaces vigorously with a cloth moistened with 

paraf

fi

 n oil in order to create a protective 

fi

 lm;

- Periodically air the premises.

6.1 STEAM GENERATOR PERIODICAL MAINTENANCE

• In case of excessive scale in the steam generator the following 
light comes on 

signalling the need to carry out descaling.

The manufacturer declines any liability if these prescriptions 
are not respected; also, the warranty does not cover the repair 
or replacement of components damaged by scale whenever 
the required supply water characteristics are not respected 
(see the relevant section).

Descaling can be carried out using two methods:
- with vinegar, concentration 100%;
- with chemical descaler (carefully following the instructions 
given below).

The appliance must be switched on for these operations.

6.1.2 METHOD WITH 100% VINEGAR   

The method with VINEGAR is carried out through GUIDED 
DESCALING.
Select "Settings" from the menu and press the button: 

 

Guided descaling

Follow the steps indicated on the oven display, as listed below:
1/5) Make sure the oven compartment is empty
2/5) Boiler preparation (emptying): wait
3/5) Filling: 

fi

 ll the boiler with pure vinegar via the upper cap until 

a beep sounds, indicating quantity reached. Given below 
are the approximate quantities of vinegar (in litres) required 
for each oven model:

6-1/1

10-1/1 20-1/1 6-2/1

10-2/1 20-2/1

gas

5

9

9

6

9

23

elec-
tric

5

5

8

7

8

15

4/5) Descaling: wait (the remaining time, including rinse, is in-

dicated).

5/5) Rinse: wait (boiler and compartment are rinsed with water 

and steam); this phase is NOT blockable.

In case of a power failure or oven switch-off during descaling 
phases 3 and 4, rinse phase 5 will ensue. If it occurs also in this 
last phase, the rinse will be carried out at the next oven switch-
on.

 6.1.3 METHOD WITH CHEMICAL DESCALER   

Descaling with chemical products must be carried out according 
to the supplier's instructions (the detergent supplier 

fi

 rms).

For example, using the ECOLAB "STRIP-A-WAY" type descaler, 
proceed as follows:
1) Close the water supply cock.
2) Completely drain the steam generator by pressing the 
following button 

3) After one minute close the steam generator drain (press the 
above-mentioned button).
4) Remove the plastic cap of the generator access tube and 
introduce the following quantity of liquid through the same:
- 2 litres of descaling liquid plus 6 litres of water (6-10gn) 
- 4.5 litres of descaling liquid plus 11.5 litres of water (20gn) 
5) Open the water cock.
6) Operate the oven STEAM cycle for 12 minutes.
7) Switch off and wait 40 minutes.
8) Switch the oven on again for another 2 minutes.
9) Switch off and wait 60 minutes.
10) With the water cock open, reopen the generator drain valve 
to empty it (press the above-mentioned button).
11) Switch the oven off.
12) Rinse the inside of the generator with a rubber hose inserted 
in the pipe, until clean water comes out the drain.
13) Re

fi

 t the cap and close the steam generator drain (press the 

above-mentioned button).

Summary of Contents for 237033

























Reviews: