manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100, Quick Start Manual

Share
Download
Electro Industries/GaugeTech Shark 100 Quick Start Manual Download Page 6

     

Doc

#    

E145703   V.1.14     

          

             QS - 6

                      Shark® 100 Meter Quickstart

Electro 

Industries/GaugeTech

™

Powered by Innovation™

Follow these steps to connect to the meter via RS485:

1. Connect the meter to the PC, using an RS485 cable. EIG offers a RS485 to USB connector, which can

    be ordered from EIG’s website: 

https://www.electroind.com/product/rs485-to-usb-communication-

    -converter/

.

2. Open CommunicatorPQA® software (see page QS-1 for the download link). 

3. Click 

Connect

 in the Icon Bar. 

4. You will see the Connect screen. Make sure

   your settings match the ones shown on the right

   (use pull-down menus). 

5. Click 

Connect

. The Device Status screen confirms

   the connection. Click OK to close the Device Status

   screen.

6. Click the 

Profile

 button on the Icon bar. 

7.The Device Profile screen opens. The tabs on the top of the screen let you choose setting

   screens. 

Summary of Contents for Shark 100









Reviews:

No comments

Brands by name

Popular brands

Load more brands