manualshive.com logo in svg

ELECTRO FREEZE COMPACT Series, Operator'S Manual, Page: 29 / 82

Share
Download
ELECTRO FREEZE COMPACT Series Operator'S Manual Download Page 29

ELECTRO FREEZE Shake Model CS705

184592

19

7

 Assembly

Correct assembly of the freezer is essential
to prevent leakage of the product and
damage to the freezer. To assemble the
freezer, you will need an approved lubricant
(such as Compound 7). Make sure all parts
of the assemblies have been washed and
sanitized before assembling. Persons
assembling the freezer must first wash and
sanitize their hands and forearms with an
approved sanitizer.

       CAUTION

To avoid electrical shock or
contact with moving parts,
make sure all switches are in
the "OFF" position and that
the main power supply is
disconnected.

1.  Persons assembling the freezer

must first wash and sanitize their hands
and forearms with an approved sanitizer.

2.

Assemble the shaft seal by install-

ing the cup seals (3) on the plastic washer
(4).  Apply a moderate amount of approved
sanitary lubricant (such as Compound 7) to
the washer. Do not allow any lubricant to
come in contact with the bell-shaped rubber
portions of the seal (figure 7-1).

3.  See figure 7-2.  Install the shaft seal

over the rear of the beater shaft. Wipe off
excess lubricant from the beater shaft.

4.   Place the scraper blades on the

beater shaft, making sure the blades are
installed properly.

5.   See figure 7-3.  Insert the as-

sembled beater shaft into the cylinder by
placing one blade on the bottom of the
cylinder.  This will center the beater and
allow alignment with the drive shaft.  Rotate
the beater assembly while pushing, until
the shank has engaged the drive shaft.

Figure 7-1  Shaft Seal Lubrication

Figure 7-3 Scraper Blade Installation

Figure 7-2 Beater Shaft Assembly

—continued

SEAL-

 

SEAL(CUP)-

BEATER SHAFT

BLADE-SCRAPER

WASHER-DOUBLE
SHAFT SEAL

BLADE-
SCRAPER

 

SHAFT-BEATER

 SEAL (CUP)-BEATER SHAFT

WASHER

WASHER

Summary of Contents for COMPACT Series



















































































Reviews:

No comments