background image

 

SnowClear Installation, Operator & Maintenance Manual

 

Outdoor Use Only 

Only install and use this product outdoors. Extremely hot when in use. Allow hot 

surfaces  to  cool  before  working  on  or  around  them.  Do  not  block  or  cover  this 
product. Also keep flammable materials away from the product to

 

prevent fires.

 

Avoid Hot Surfaces 

Avoid skin  contact  with  hot  surfaces  to  prevent  burns.  Allow  hot  surfaces  to  cool 
before  working  on  or  around  them.  Ensure  the  heating  elements  are  cool

 

before

 

performing any maintenance or inspections.

  

Risk of Fire 

High temperature, risk of fire, keep electrical cords, drapery, furnishings and other 
combustibles at least 0.9 m (3 feet) from the front on the heater and away from the 
side  and  rear.  To  reduce  the  risk  of  fire,  do  not  store  or  use

 

gasoline  or  other

 

flammable vapors and liquids in the vicinity of the unit.

  

High Temperature Porcelain Wire Connectors 

Only high temperature porcelain wire connectors are to be used for connecting the 

heating  elements  to  the  unit.  High  temperature  porcelain

 

wire  connectors  are

 

supplied with this product.

 

Handling of the Unit 

Handle product with care to prevent damage to the heating elements. Do not

 

splash 

water on the heating elements. 

 

 

 

 

 

 

 

 

 

SAVE THESE INSTRUCTIONS 

Summary of Contents for SnowClear TK-C4000























Reviews: