manualshive.com logo in svg

Elba EGC 833 series, Instructions For The Use, Page: 19 / 32

Share
Download
Elba EGC 833 series Instructions For The Use Download Page 19

19

GAS INSTALLATION REQUIREMENTS
Important !

• 

The walls adjacent to the cooker must be of heat-resistant material.

• 

Before installation, make sure that the local distribution conditions (gas type 

and pressure) and the adjustment of this appliance are compatible. The applian

-

ce adjustment conditions are given on the plate or the label.

• 

This appliance must be installed and serviced only by a suitably qualified, regi

-

stered installer. The installer shall refer to the local standards in force.

• 

Failure to install the appliance correctly could invalidate any manufacturer’s 

warranty.

This appliance is supplied for use on Natural gas, LPG or Town Gas (check the gas regu-

lation label attached on the appliance).

• 

Appliances supplied for use on Natural gas: they are adjusted for this gas only and 

cannot be used on any other gas (LPG or Town gas) without modification.

 

The appliances are manufactured for conversion to LPG and Town gas.

• 

Appliances supplied for use on LPG: they are adjusted for this gas only and cannot be 

used on any other gas (Natural or Town gas) without modification.

 

The appliances are manufactured for conversion to Natural and Town gas.

• 

Appliances supplied for use on Town gas: they are adjusted for this gas only and can-

not be used on any other gas (Natural gas or LPG) without modification.

 

The appliances are manufactured for conversion to Natural gas and LPG.

If the Natural gas/LPG/Town gas conversion kit is not supplied with the appliance this kit 

can be purchased by contacting the After-Sales Service.

GAS SECTION

7

Summary of Contents for EGC 833 series

































Reviews:

No comments