background image

160

……

191 

……

 

192

……

223 

……

 

224

……

255 

……

 

15 

fanction 

Reset 

164--191 

Auto 

11. Trouble Shooting

Listed below are a few common problems that you may encounter, with solutions. 

Unit does not work, no light output and the fan does not work;

1.

Check the power connection and main fuse.

2.

Be sure the voltage of the connector.

Not responding to DMX Control;

1.

After connecting the controller, the lamp should be working. If it does not work properly, please
check if the signal plug and power cable is connected correctly.

2.

If the DMX LED is on and no response to the channel, check the address settings and the polarity
of DMX output voltage.

3.

If the signal of the product is unstable, 

please check the input terminal and 

circuit boards

.

4.

Try using another DMX controller.

5.

Check  to  see  if  the  DMX  cables  run  near  or  run  alongside  to  high  voltage  cable.  It  may  cause

damage or interference to DMX interface circuit.

One of the channels is not working:

1.

The stepper motor might be damaged or the cable connected to the PCB is broken.

2.

The motor’s drive IC on the PCB might be out of condition.

12. FIXTURE CLEANING

The  cleaning  of  internal  and  external  optical  lenses  and/or  mirrors  must  be  carried  out  periodically  to 
optimize light output. 
Cleaning  frequency  depends  on  the  environment  in  which  the  fixture  operates:  damp,  smoky  or 
particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. 
Clean with soft cloth using normal glass cleaning fluid. 
Always dry the parts carefully. 
Clean the external optics at least every 20 days. Clean the internal 
optics at least every 30/60 days. 
Clean the fans on the head and base every 20 days. 
Disconnect the fixture before clear. 

Summary of Contents for PG-300W-IP



















Reviews: