background image

LUPUS2K - VOLANS2K

 - TECHNICAL MANUAL - 

090001113

[email protected]
elmospa.com

16

12. TRANSMITTER CONFIGURATION VIA SOFTWARE

The transmitter can be fully programmed by using BrowserOne v. 3.4.7 or higher with the module for the control unit v. 

8.4.11 or higher. The control unit firmware must be 8.2.0.0 or higher. 

See the specific technical documentation for information on other expressly compatible control unit models.

Perform the following operations:

•  Start the connection as explained in the programming manual of the control unit.

•  Read the current configuration, open the “

Zones

” page and identify the number of the zone that is assigned the 

acquired code of the transmitter. 

•  Still in the Zones page, open the “

Radio devices NG-TRX

” tab.

On the side of the page concerning the NG-TRX wireless devices, some useful notes are displayed for the correct 

configuration of the detector, depending on the selection of the “

Supervision interval

” and the “

Tx Boost

” function. 

In the bottom page you can find the specific section for the transmitter channels configuration, described in chapter “10. 

ELECTRICAL CONNECTIONS”.

Event type for each channel.

Press to delete the acquired code.

The picture highlights the 
informations concerning the 
radio NG-TRX system, the 
firmware version and the 
transmitter model.

Activates the internal buzzer of the transmitter in 

alarm or reset for a local operation check of all 

channels (unless differently set for each single 

channel). 

Default

: disabled (any anomaly is 

signalled in any case).

Function available only if you set a precise 

supervision interval; it allows you to delay the 

anomaly signal generated by the “supervision 

failure” signal.

Select to increase the power of the RF section. 

WARNING: this causes a decrease in battery duration.

 Use only when the range is not 

sufficient.

You can choose between “

Automatic

”, “

Minimum 

consumption

” to maximize battery life when the 

signal reception is sufficient, “

Maximum power

” 

in case of high limitations due to adverse site 

conditions (drawback: battery life reduction). 

Default

: Automatic.

Set the periodic transmission cadence necessary 

for the control unit to detect the transmitter control 

failure, with the consequent reporting and alert 

actions settable from other software pages.

Setting a short interval will affect the battery 

duration of the device. In the Default condition, the 

general parameters will be used: they are set in the 

“System options” page for the NG-TRX devices.

These two lines are 

actually only one, whose 

content changes.

Example

Summary of Contents for NG-TRX LUPUS2K





















Reviews: