- 17 -
Intel LGA 115x
Rückwand
3. INSTALLATION - INTEL LGA-115X-BUCHSE
SCHRITT 1: ENTFERNEN DES
MOTHERBOARDS
Wenn Ihr PC-Gehäuse keinen Ausschnitt von
der unteren CPU-Seite des Motherboards hat,
müssen Sie zuerst das Motherboard von Ihrem
Computer entfernen.
SCHRITT 2: BEFESTIGEN SIE DIE
RÜCKWAND AM MOTHERBOARD
Installieren Sie die Intel-Rückwand für die
LGA-115x-Buchse auf der Rückseite Ihres
Motherboards. Richten Sie die Bohrungen
auf dem Motherboard entsprechend den
Bohrungen auf der Rückwand aus.
SCHRITT 3: BEFESTIGUNGSSCHRAU-
BEN ANBRINGEN
Installieren Sie mittels der vier LGA-115x
Flügelbefestigungsschrauben Ihr Mother-
board an der Rückplatte.
Die Fingerschrauben sind ohne die Verwendung
von Werkzeugen (d. h. Zangen) anzubringen.
Beginnen Sie mit der Befestigung von zwei Fin-
gerschrauben gleichzeitig, vorzugsweise kreuz-
weise, aber nicht vollkommen festziehen bis alle
vier Schrauben teilweise eingeschraubt sind.
SCHRITT 6: ANBRINGUNG VON
MONTAGEHALTERUNGEN
Verwenden Sie vier M4 x 4-Schrauben, um
zwei Intel-Halterungen an der Pumpeneinheit
anzubringen.
Es muss darauf geachtet werden, dass die
vorab aufgebrachte Wärmeleitpaste nicht
berührt oder beschädigt wird!
SCHRITT 4: EINBAU DER LÜFTER IN
DEN KÜHLER
Befestigen Sie die Lüfter (1x, 2x oder 3x, je
nach AIO-Version) mit den Schrauben UNC
6-32 x 30 mm am Kühler.
UNC
6-32 x 30 mm
Lüfter
Kühler
SCHRITT 5: ENTFERNEN DER
KÜHLPLATTENSCHUTZFOLIE
Die Schutzabdeckung von der Rückseite
der Pumpeneinheit entfernen, um eine
Beschädigung der Kühlplatte und der vorab
aufgebrachten Wärmeleitpaste auf der
Kühlplatte zu vermeiden.
Beim Entfernen der Schutzabdeckung und bei
der Installation muss darauf geachtet werden,
dass die vorab aufgebrachte Wärmeleitpaste
nicht berührt oder beschädigt wird!
SCHRITT 7: INSTALLATION DER
PUMPENEINHEIT
Wischen Sie die Kontaktfl äche der CPU ab (mit
einem nicht scheuernden Tuch oder einem
Wattestäbchen, wie im Beispielbild gezeigt).
Richten Sie die Pumpeneinheit, wie
in der Abbildung gezeigt, über den
Befestigungsschrauben und der CPU aus.
Legen Sie die beiliegenden Druckfedern und
Flügelmuttern über die Befestigungsschrauben
(4x). Ziehen Sie zunächst zwei Flügelmuttern
hintereinander an, vorzugsweise überkreuz,
und ziehen Sie sie erst dann fest, wenn alle
eingeschraubt und etwas angezogen wurden.
Flügelbefesti-
gungsschraube
für INTEL LGA
115x / AMD AM4
Buchse
M4x4
Intel
Montagehalterung
Flügelmutter
Feder
Nicht
scheuerndes
Tuch
IHS
Schutzabdeckung
Vorab
aufgebrachte
Wärmeleitpaste
Summary of Contents for EK-AIO Elite 280 D-RGB
