background image

   
DK50 4VR/50

 

       

 

04/2018 

- 25 -   

NP-DK50 4VR50-11_04-2018 

 

15.9.  Clean the cooler ribs and the fan 

 

For permanently high efficiency, it is necessary to maintain the whole equipment and especially the cooler´s 
fan and the cooler itself clean – 1x year suck or blow settled dust out with compressed air from the surface of 
the cooling ribs and the fan. 
 
 

16. 

STORAGE  

If the compressor will not be used for a prolonged time period, drain any condensate from the air tank.  Then 
turn on the compressor for 10 minutes, keeping the drain valve open (1) (Fig.10).  Switch off the compressor 
by  switch  (3)  at  pressure  switch  (2)  (Fig.9),  close  the  drain  valve  and  disconnect  the  appliance  from  the 
mains. 
 
 

17. 

DISPOSING OF THE APPLIANCE  

•  Disconnect the appliance from the mains. 
•  Release air pressure in the pressure tank by opening the drain valve (1) (Fig.10). 
•  The components of the product are non-toxic. 
•  Dispose of the appliance following all environmental regulations.    
   
 

18. 

REPAIR SERVICE 

Guaranteed and post-guarantee repairs must be done by the manufacturer, its authorized representative, or 
service personnel approved by the supplier. 
The manufacturer reserves the right to make changes to the appliance without notice.  Any changes made 
will not affect the functional properties of the appliance. 
 
 

19. 

SOLVING PROBLEMS 

Caution!    Before  proceeding,  depressurize  the  air  tank  to  zero  and  disconnect  the 
appliance from the mains. 
 

 
The internal surfaces of the air tank must be cleaned and all condensed liquid must be removed after a dryer 
failure. 

 
Check the dew point of the air leaving the air tank (see Chapter 5 - Technical Data) in order to protect 
connected equipment from damage! 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for DK50 4VR/50




























Reviews: