background image

29 

 

sub-menu is arranged by hierarchy. 

Some menus contain only one item of information, but most menus contain more than one item of information 
and open each item folder to access the next level of sub menus. Expand the table through the grid option, enter a 
group of execution commands through the dialog box option, and return to the upper menu regardless of the 
interface by pressing the left direction button. 

The names of all nine sub menus are shown in bold on the main menu and below the icon. When entering the 
stepped menu, the name of the sub menu or the path you are in is displayed at the top of the screen. 

 

 

 

 

 

Fault Diagnosis menu 

On the main menu, Select Diagnostics and press Select to access the Fault diagnosis menu. The Fault diagnosis 
menu contains Present Errors current faults and Fault History historical faults 

Note: Sometimes a fault caused by a temporary event captured in the circuit is not a system fault. You can 
determine whether the fault exists by restarting the system and observing whether the fault disappears 
automatically. 

Summary of Contents for EK18RF
































Reviews:

Related manuals for EK18RF