background image

 

 

 

 

Page 3 of 12 

Drawing   : - TPC499 
Issue 

: - 1 

Date 

: - 29/01/20 

 
 

UNPACKING

 

 

Carefully remove the CD30S dehumidifier unit from its transit box and visually 
check  for  signs  of  transit  damage.  If  there  is  evidence  of  damage  DO  NOT 
attempt  to  operate  the  unit,  call  your  supplier  for  advice.  Do  not  discard  the 
packing; it will be useful when transporting the dehumidifier unit in the future. 

 

INTRODUCTION 
 

The  Ebac  CD30S  industrial  dehumidifier  removes  moisture  from  the  air 
through the refrigeration process. 
 
The Ebac CD30S is basically comprised of: 
 

A)

  A compressor 

B)

  A refrigerant evaporator coil 

C)

  A refrigerant condenser coil 

D)

  One circulation fan 

E)

  A drain tray for collecting and disposing of condensed moisture 

F)

  A solid state timer for hot gas defrost cycle 

G)

  An adjustable membrane-type humidistat 

H)

  A cabinet to house the above components 

 
The fan draws the moist air through the cold evaporator coil which cools the 
air below its dew point. Moisture forms on the evaporator coil and is collected 
in the condensate tray which is equipped with a permanent drain. The cooled 
air then passes through the hot condenser coil where it is reheated using the 
same  energy  removed  during  the  cooling  phase  plus  the  additional  heat 
generated  by  the  compressor.  The  air  is,  therefore  discharged  from  the 
dehumidifier  at  a  slightly  higher  temperature  with  a  lower  absolute  humidity, 
than that which entered. Continuous circulation of air through the dehumidifier 
gradually reduces the relative humidity within the area. 
The CD30S dehumidifier is a rugged reliable drying unit designed to operate 
effectively  over  a  broad  range  of  temperature  and  humidity  conditions.  A 
powerful  and  reliable  active  hot  gas  defrost  system,  controlled  by  an 
electronic timer, guarantees positive de-icing, thereby optimizing operation at 
low temperatures. 
The  unit  incorporates  a  welded  steel  chassis  and  is  finished  in  an  epoxy 
coating for resilience to damage caused by rough handling. 
The CD30S dehumidifier is fitted with an adjustable humidistat to enable you 
to select the level of dryness. 

Summary of Contents for CD30S













Reviews: