GB
- 16 -
Important!
When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with
due care. Keep this manual in a safe place, so
that the information is available at all times. If
you give the equipment to any other person, give
them these operating instructions as well.
We accept no liability for damage or accidents
which arise due to non-observance of these inst-
ructions and the safety information.
1. Safety information
The corresponding safety information can be
found in the enclosed booklet.
Caution!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock,
fi
re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
2. Layout and items supplied
2.1 Layout
1. Miter stop
2. Parallel stop
3. Wheel guard
4. Cutting table
5. Water trough
6. Housing
7. Knurled screw for setting the angle
8. Scale for miter cut
9. Knurled
screw
10. Thumb screw
11. Holder for splitter
12. On/O
ff
switch
13. Switch housing
14. Cable holder
15. Diamond cutting wheel
16. Outer
fl
ange
17. Side cover
18. Nut
19. Splitter
20. Fastening screws for splitter holder
2.2 Items supplied
Please check that the article is complete as spe-
ci
fi
ed in the scope of delivery. If parts are missing,
please contact our service center or the nearest
branch of the DIY store where you made your
purchase at the latest within 5 work days after
purchasing the article and upon presentation of
a valid bill of purchase. Also, refer to the warranty
table in the warranty provisions at the end of the
operating instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
IMPORTANT
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or su
ff
ocating!
•
Original operating instructions
•
Safety information
3. Technical data:
Motor rating: ............................600 W S2 10 min
Motor speed: ........................................ 2950 rpm
AC motor ....................................... 230 V ~ 50 Hz
Insulation material class .......................... Class B
Protection type ............................................ IP 54
Protection class ................................................. I
Cut length: ............................................ Unlimited
Jolly length: .......................................... Unlimited
Cutting height 90°: .................................... 35 mm
Cutting height 45°: .................................... 22 mm
Cutting table-Dimensions ....... 330 mm x 360 mm
Diamond cutting wheel ........... ø 180 x ø 25.4 mm
Weight: .......................................................7,9 kg
A load factor of S2 10 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (600 W)
for no longer than the time stipulated on the spe-
ci
fi
cations label (10 minutes ON period). If you fail
Anl_TH_TC_618_SPK1.indb 16
Anl_TH_TC_618_SPK1.indb 16
21.02.13 13:40
21.02.13 13:40
Summary of Contents for TH-TC 618
Page 11: ...D 11 Anl_TH_TC_618_SPK1 indb 11 Anl_TH_TC_618_SPK1 indb 11 21 02 13 13 40 21 02 13 13 40...
Page 89: ...89 Anl_TH_TC_618_SPK1 indb 89 Anl_TH_TC_618_SPK1 indb 89 21 02 13 13 41 21 02 13 13 41...
Page 90: ...90 Anl_TH_TC_618_SPK1 indb 90 Anl_TH_TC_618_SPK1 indb 90 21 02 13 13 41 21 02 13 13 41...
Page 91: ...91 Anl_TH_TC_618_SPK1 indb 91 Anl_TH_TC_618_SPK1 indb 91 21 02 13 13 41 21 02 13 13 41...
