GB
- 31 -
lawn mower turns about and drives in a di
ff
erent
direction within the area. All zones that you wish
to protect within the lawn area – e.g. garden
ponds, trees, furniture or
fl
ower beds – must be
cordoned o
ff
by the perimeter wire (18). The pe-
rimeter wire (18) must form a closed circuit. If the
robot lawn mower bumps into an obstacle within
the mowing area, it reverses and then continues
mowing in a di
ff
erent direction (Fig. 3).
5.2 Sensors
The robot lawn mower is equipped with a number
of safety sensors.
•
Lifting sensor:
If the robot lawn mower is lifted by more than
30° from the ground at the back, the robot
lawn mower and the rotation of the blades
(10) are stopped immediately.
•
Tilting sensor:
If the robot lawn mower tilts severely in any di-
rection, the robot lawn mower and the rotation
of the blades (10) are stopped immediately.
•
Obstruction sensor:
The robot lawn mower is able to detect obsta-
cles in its path. If the robot lawn mower colli-
des with an obstacle, the robot lawn mower
and the rotation of the blades will be stopped
immediately and the mower will reverse away
from the obstacle.
•
Rain sensor:
The robot lawn mower is equipped with a rain
sensor (5) to prevent the robot lawn mower
from operating in the rain. The robot lawn mo-
wer returns to the charging station (19) when
it detects rain and is completely recharged
there. Once the rain sensor (5) is dry again,
the robot lawn mower will stay in the charging
station (19) for another two hours.
5.3 Preparations
First, draw a sketch of your lawn. Include obstac-
les in your sketch and draw up a plan for how you
intend to protect them. This will make it easier to
fi
nd a good position for the charging station (19)
and to lay the perimeter wire (18) around bushes,
fl
ower beds, etc (Fig. 4).. If the grass is taller than
60 mm it has to be shortened
fi
rst to avoid expo-
sing the robot lawn mower to excessive load and
adversely a
ff
ecting its operating e
ffi
ciency. Use a
conventional lawn mower or trimmer to do this.
Remove all loose objects from the lawn which
could get damaged by the robot lawn mower or
damage the robot lawn mower itself.
Have the following tools ready: A hammer, tongs,
a wire stripper and a spirit level (optional).
5.4 Charging station
5.4.1 Position of the charging station
Determine the best position for the charging sta-
tion
fi
rst (19). An outdoor socket outlet is required
which supplies a permanent supply of electricity
so that the robot lawn mower works at all times.
The charging station (19) must be placed on a
fl
at area at the level of the turf. Make sure that the
area is
fl
at and dry. Select a position which is in
the shade, because it is best if the rechargeable
battery (22) is charged up in a cool area (Fig. 5a).
Also note that the perimeter wire has to be laid in
a straight line for least 2 m in front of the charging
station (19). Curves immediately in front of the
charging station (19) could cause problems when
docking for charging.
5.4.2 Localization of the charging station
When the rechargeable battery (22) is almost em-
pty, the robot lawn mower returns to the charging
station (19) by following the perimeter wire (18) in
a counterclockwise direction until it reaches the
charging station (19). Make sure, therefore, that
the charging station (19) faces in the right direc-
tion when you position it (Fig. 5b).
5.4.3 Connecting the charging station to the
power supply unit
1. Before you connect the charging station (19)
to the power supply, check that the mains po-
wer supply is 100-240 V at 50/60 Hz.
2. Connect the power supply unit (13) directly to
a socket outlet. Do not use the cable for any
other use.
3. Do not use the power supply unit if it is da-
maged (13). In the event of any damage to
cables or the power supply unit (13), contact
an authorized professional immediately for
replacement.
4. Do not charge up the robot lawn mower in a
damp location. Do not charge up the robot
lawn mower at temperatures above 40°C or
below 5°C.
5. Keep the robot lawn mower and the power
supply unit (13) away from water, sources of
heat and chemicals. Keep the cable of the po-
wer supply unit (13) away from sharp edges
in order to prevent damage.
6. Connect the power supply unit (13) to the
charging station (19) (Fig. 5c).
To charge up the rechargeable battery (22) for
the robot lawn mower straight away while you
are still doing the installation work,
fi
rst switch on
the robot lawn mower with the main switch (7)
Anl_GC_RM_500_SPK9.indb 31
Anl_GC_RM_500_SPK9.indb 31
16.02.2021 14:17:32
16.02.2021 14:17:32
