EINHELL BT-SM 2131 DUAL, Operating Instructions Manual

Page: 24 / 150

and with light pressure downwards until the saw
blade (7) has completely cut through the
workpiece.
With the drag guide (23) not fixed in place: Pull
the machine head (4) all the way to the front and
then use the handle to move it downwards
steadily and with light pressure. Now push the
machine head (4) slowly and steadily to the very
back until the saw blade (7) has completely cut
through the workpiece.
When the cutting operation is completed, move
the machine head (4) back to its upper (home)
position and release the ON/OFF button (2).
Important. The integral resetting springs will
automatically lift the machine head. Do not simply let
go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counter pressure as it does so.
7.2 Cross cut 90° and turntable 0° - 45°
(Fig. 1-3, 12)
The crosscut saw can be used to make crosscuts of
0°- 45° to the left and 0° - 45° to the right in relation to
the stop rail.
Release the turntable (17) by slackening the
locking screw (14).
Turn the turntable (17) and scale pointer (15) to
the desired angular setting on the dial (16) and
lock into place with the locking screw (14). The
saw has locking positions at angles of - 45°, -
31.6°, -22.5°, -15°, 0°, 15°, 22.5°, 31.6° and 45°,
at which the turntable (17) audibly clicks into
position.
Retighten the locking screw (14) to secure the
turntable (17) in place.
Cut as described under section 7.1.
7.3 Miter cut 0°- 45° and turntable 0° (Fig. 1-3, 13)
The crosscut saw can be used to make miter cuts to
the left of 0°-45° and to the right of 0°-45° in relation
to the work surface.
If required, dismantle the clamping device (8) or
mount on the opposite side of the fixed saw table
(18).
Move the machine head (4) to its upper position.
Fasten the turntable (17) in 0° position.
Adjust the miter angle on the machine head and
the stop rail as described under points 6.5 and
6.6.
Cut as described under section 7.1.
7.4 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 1-3, 14)
The crosscut saw can be used to make miter cuts to
the left of 0°-45° and to the right of 0°-45° in relation
to the work surface, with simultaneous setting of the
turntable from 0°-45° to the left or 0°-45° to the right in
relation to the stop rail (double miter cut).
If required, dismantle the clamping device (8) or
mount on the opposite side of the fixed saw table
(18).
Move the machine head (4) to its upper position.
Release the turntable (17) by slackening the
locking screw (14).
Use the handle (1) to adjust the turntable (17) to
the angle required (in this connection see also
section 7.2).
Retighten the locking screw (14) to secure the
turntable in place.
Adjust the miter angle on the machine head and
the stop rail as described under points 6.5 and
6.6.
Cut as described under section 7.1.
7.5 Limiting the cutting depth (Fig. 15)
The cutting depth can be infinitely adjusted using
the screw (27). Turn the screw (27) in or out to set
the required cutting depth and then retighten the
knurled nut on the screw (27).
Check the setting by completing a test cut.
7.6 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (22) for
sawdust and chips.
The debris bag (22) can be emptied by means of a
zipper at the bottom (1).
7.7 Changing the saw blade (Fig. 1, 16-18)
Before changing the saw blade: Remove the
power plug!
Wear work gloves to prevent injury when
changing the saw blade.
Swing the machine head upwards (4).
Undo the screw (z) on the cover plate (f) of the
saw blade.
Pull back the adjustable blade guard (6) and at
the same time turn the cover plate to achieve
access to the flange bolt.
Press the saw shaft lock (5) with one hand while
positioning the Allen key (d) on the flange bolt
(31) with the other hand. The saw shaft lock (5)
engages after no more than one rotation.
Now, using a little more force, slacken the flange
screw (31) in the clockwise direction.
Turn the flange screw (31) right out and remove
the external flange (32).
Take the blade (7) off the inner flange and pull out
22
GB
Anleitung_BT_SM_2131_Dual_SPK7:_ 14.10.2010 15:39 Uhr Seite 22