background image

12-VOLT LITHIUM-ION GRASS/SHRUB SHEAR — CHT2000E

EN

 

č

Wipe the surface with a dry cloth.

 WARNING: 

Never use water for cleaning your tool. 

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to damage from various types of 
commercial solvents. Use clean clothes to remove dirt, 
dust, oil, grease, etc.

SHARPENING THE CUTTING BLADE

1.  Remove the battery pack.

2.  Clamp the blade assembly in a vise and file the 

exposed cutting surface of each blade tooth. Remove 
as little material as possible.

3.  Remove the grass/shrub shear from the vise and 

adjust the unsharpened blade on the other side 
exposed. Repeat the above procedures until all the 
blade teeth sharpened.

NOTICE: 

Do not operate your tool with dull or damaged 

cutting blades. This may cause overload and will give 
unsatisfactory cutting results.

LUBRICATING THE BLADE

For best operation and longer blade life, lubricate the 
tool blade with light weight machine oil before and after 
each use. 

Remove the battery pack and lay the tool onto a flat 
surface. Apply the oil along the edge of the top blade. 

NOTICE: 

For extended using period, oil the blade during 

cutting operation.

TRANSPORTING AND STORING

 

č

Always place the shield on the blade before storing or 
transporting the tool. Use caution to avoid the sharp 
teeth of the blade.

 

č

Clean the tool thoroughly before storing.

 

č

Store the tool indoors, in a dry place that is 
inaccessible to children.

 

č

Keep away from corrosive agents such as garden 
chemicals and deicing salts.

 WARNING: 

Blades are sharp. When handling the 

blade assembly, wear non-slip, heavy-duty protective 
gloves. Do not place your hand or fingers between blades 
or in any position where they could get pinched or cut. 
NEVER touch blades or service the unit with battery pack 
installed.

Protecting the environment

Do not dispose of electrical equipment, 
battery charger and batteries/
rechargeable batteries into household 
waste!

According to the European law  
2012/19/EU, electrical and electronic 
equipment that is no longer usable,and 
according to the European law 2006/66/EC, 
defective or used battery packs/batteries, 
must be collected separately.

If electrical appliances are disposed of in 
landfills or dumps, hazardous substances 
can leak into the groundwater and get into 
the food chain, damaging your health and 
well-being.

20

Summary of Contents for CHT2000E

























Reviews: