EF HB BI 2721 A User Manual Download Page 2

Dear Customer, 

 

 

Thank you for having purchased and given your preference to our product. This manual 
provides  a  means  to  make  full  use  of  the  features  of  this  product.  The  safety 
precautions and recommendations are also featured in this manual. We recommend 
that you read this manual for best performance and to extend the life of your appliance. 

 

 

Please preserve this manual for future use, in the event that doubts arise relating to 
the operation.

 

 

                                                                      

 

Installation

 

Electrical Shock Hazard

 

 

Disconnect the appliance from the mains electricity supply before carrying 
out any work or maintenance on it.

 

 

Connection to a good earth wiring system is essential and mandatory.

 

 

Alterations to the domestic wiring system must only be made by a qualified 
electrician.

 

 

Failure to follow this advice may result in electrical shock or death.

 

 

Cut Hazard

 

 

Panel edges are sharp – be careful

 

 

Failure to use caution could result in injury or cuts.

 

 

Important Safety Instructions

 

 

After  having  unpacked  the  appliance,  check  to  ensure  that  it  is  not 
damaged.

 

 

No combustible material or products should be placed on this appliance at 
any time.

 

IMPORTANT: This appliance is designed and manufactured solely for the cooking 
of domestic (household) food and is not suitable for any non-domestic application 
and therefore should not be used in a commercial environment.  

The appliance guarantee will be void if the appliance is used within a non-domestic 
environment i.e. A semi commercial, commercial or a communal environment. 

 

SAFETY GUIDELINES 

Summary of Contents for HB BI 2721 A

























Reviews: