SECTION 3:
INSTALLATION
3-4
BATS
0018257_REV_A
Attaching Hydrophone to Angle Mount
CAUTION!
When mating connectors DO NOT allow any silicone spray (or grease) to
contact the black potting of the hydrophone. Should silicone come in
contact with the hydrophone potting, proper sound transfer from water
to hydrophone will be prevented. Attempting to remove silicone from the
hydrophone can damage the potting material.
NOTE:
If using an extension pipe with a sufficient inside diameter to allow
the hydrophone cable to be fed through to the hydrophone, remember
to run the cable through the pipe before placing the 1/2-inch (13-mm)
bolts in the mounting holes, as the connector may not pass through when
the bolts are in place. When drilling the lower hole, keep in mind that you
need enough space between the end of the pipe and the connector on
the top of the hydrophone itself to connect and disconnect the cable. For
this reason, we recommend the lower mounting hole be no more than 2
inches (5 cm) from the end of the pipe.
The hydrophone centerline, or zero bearing, is indicated by the index mark. The index mark is just above
the potted section of the hydrophone which is aligned with the slot in the pressure case as opposed to
the pin which faces aft or 180° from bow reference and is generally aligned so that it corresponds to the
vessel heading. Most operations requiring a portable tracking system will be on various vessels of
opportunity, and require a quick and temporary mounting.
hydrophone mounting arrangement.
1.
Fasten the hydrophone to the Hydrophone Mount Angle Bracket (not supplied), shown in
, by aligning the slot in the PVC base with the “V” in the bracket. Align the screw clamps to
secure the hydrophone to the angle bracket with the grooved areas on the hydrophone case.
2.
Feed the deck cable, Model 4113C or 4113C-DT, through the hydrophone extension pipe. Connect
the deck cable to the hydrophone. See
for the Model 4113C and 4113C-
DT cable assemblies. The Deck Cable mates to the Hydrophone by lining up the pins in both
connectors and pushing together. Mated connections are held together with locking sleeves.
3.
Fasten the hydrophone and angle bracket to the extension pipe. Use screw eyes or other fasteners
for fore and aft guy attachments.
Summary of Contents for USBL BROADBAND ACOUSTIC TRACKING SYSTEM
