Edgetech 2000-TVD User Hardware Manual Download Page 52

Page: 52 / 111

3-4

3.0: SETUP AND ACTIVATION

2000-TVD COMBINED SONAR

0017424_REV_B

USB:

(5) USB connectors. Four USB 2.0 ports two on the back panel
and two on the front. One USB 3.0 port on the back panel

VAC INPUT:

CEE-type AC input connector. Connects to 90–260 VAC, 50/60 Hz
power.

In addition, COM5–COM8 serial ports are available for use as required, each with DB-9 male connectors.
These connectors are located on the back panel.

3.5.2

Topside Computer Controls and Indicators

The Topside Computer includes controls and indicators on the front and back panels, as shown in

and

, are the following:

POWER:

Rocker switch. Switches AC power to the Topside Computer. This
switch can be left in the on position at all times.

SYSTEM POWER (switch):

Push button toggle switch. Turns the Topside Computer on or off.

SYSTEM POWER (indicator):

Green indicator. Illuminated when the Topside Computer is on.

RESET:

Momentary push button switch. Resets the Topside Computer.

HDD:

Yellow indicator. Flashes when a hard drive on the Topside
Computer is being accessed.

Summary of Contents for 2000-TVD
















































































































Search results

Summary of Contents for 2000-TVD

Reviews:

Related manuals for 2000-TVD

Brands by name

Popular brands

Edgetech 2000-TVD, User Hardware Manual

Search results

Summary of Contents for 2000-TVD

Reviews:

Related manuals for 2000-TVD

Brands by name

Popular brands