Edge Products Juice Attitude Installation Instructions Manual Download Page 10 | Manualshive

Page: 10 / 24

Edge Products Juice Attitude Installation Instructions Manual Download Page 10

1999 to 2000

2001-2003

NOTE: The two figures above are

showing underneath the dash

console near the brake and accel-

erator pedals.

11. Connect the TPS connec-

tors in between the stock har-

ness and the sensor as shown.

12. From in the cab, route the

TPS Sensor harness through

the fire wall and into the engine

compartment.

NOTE: Route through the existing

holes located on the fire wall.

13. Locate the TPS Adapter

wire.

14. Plug the single wire adapt-

er into the end of the TPS Sen-

sor harness.

This concludes the Juice Har-

ness installation. Please refer

to the EGT PROBE INSTALLA-

TION section of this manual to

continue your installation.

Brake

Linkage

TPS Sensor

TPS Adapter - Edge

Truck

Harness

Accelerator Linkage

Brake

Linkage

TPS Sensor

Edge TPS

Adapter

Truck

Harness

Accelerator

Linkage

Stock

Harness

TPS

Sensor

Plugs into Main Juice harness

«
...
8
9
10
11
12
...
»

Summary of Contents for Juice Attitude

























Reviews:

No comments