manualshive.com logo in svg

Edge-Core ECS4810-12M, Installation Manual, Page: 6 / 76

Share
Download
Edge-Core ECS4810-12M Installation Manual Download Page 6

C

OMPLIANCES

 

AND

 S

AFETY

 S

TATEMENTS

–  6  –

CE M

ARK

 D

ECLARATION

 

OF

 C

ONFORMANCE

 

FOR

 EMI 

AND

 S

AFETY

 (EEC)

This information technology equipment complies with the requirements of the 
Council Directive 89/336/EEC on the Approximation of the laws of the Member 
States relating to Electromagnetic Compatibility and 73/23/EEC for electrical 
equipment used within certain voltage limits and the Amendment Directive 93/
68/EEC. For the evaluation of the compliance with these Directives, the following 
standards were applied:

RFI Emission:

◆

Limit according to EN 55022:2007, Class A/B

◆

Limit for harmonic current emission according to EN 61000-3-2:2006, 

Class A

◆

Limitation of voltage fluctuation and flicker in low-voltage supply 

system according to EN 61000-3-3:2005

Immunity:

◆

Product family standard according to EN 55024:2001 + A2:2003

◆

Electrostatic Discharge according to IEC 61000-4-2:2008

◆

Radio-frequency electromagnetic field according to IEC 61000-4-

3:2007

◆

Electrical fast transient/burst according to IEC 61000-4-4:2004

◆

Surge immunity test according to IEC 61000-4-5:2005

◆

Immunity to conducted disturbances, Induced by radio-frequency 

fields: IEC 61000-4-6:2008

◆

Power frequency magnetic field immunity test according to IEC 

61000-4-8:2001

◆

Voltage dips, short interruptions and voltage variations immunity test 

according to IEC 61000-4-11:2004

LVD:

◆

EN60950-1:2006+A11:2009 

Summary of Contents for ECS4810-12M













































































Reviews:

No comments