Edge-Core ECS4810-12M Installation Manual Download Page 35 | Manualshive

Page: 35 / 76

Edge-Core ECS4810-12M Installation Manual Download Page 35

C

HAPTER

2

| Installing the Switch

Mounting

– 35 –

R

ACK

M

OUNTING

Before rack mounting the switch, pay particular attention to the following
factors:

◆

Temperature: Since the temperature within a rack assembly may be higher
than the ambient room temperature, check that the rack-environment
temperature is within the specified operating temperature range.

◆

Mechanical Loading: Do not place any equipment on top of a rack-mounted
unit.

◆

Circuit Overloading: Be sure that the supply circuit to the rack assembly is
not overloaded.

◆

Grounding: Rack-mounted equipment should be properly grounded.
Particular attention should be given to supply connections other than direct
connections to the mains.

To rack-mount devices:

1.

Attach the brackets to the device using the screws provided in the Bracket
Mounting Kit.

Figure 8: Attaching the Brackets

2.

Mount the device in the rack, using four rack-mounting screws (not
provided).

«
...
33
34
35
36
37
...
»

Summary of Contents for ECS4810-12M













































































Reviews:

No comments