Edge-Core ECS4810-12M Installation Manual Download Page 54 | Manualshive

Page: 54 / 76

Edge-Core ECS4810-12M Installation Manual Download Page 54

A

PPENDIX

A

| Troubleshooting

Power and Cooling Problems

– 54 –

P

OWER

AND

C

OOLING

P

ROBLEMS

If the power indicator does not turn on when the power cord is plugged in, you
may have a problem with the power outlet, power cord, or internal power
supply. However, if the unit powers off after running for a while, check for loose
power connections, power losses or surges at the power outlet. If you still
cannot isolate the problem, the internal power supply may be defective.

I

NSTALLATION

Verify that all system components have been properly installed. If one or more
components appear to be malfunctioning (such as the power cord or network
cabling), test them in an alternate environment where you are sure that all the
other components are functioning properly.

ALM/MJR LED is Red

◆

One or more major system alarm(s) affecting traffic have

occurred.

◆

Check the alarm filter mask to determine potential cause(s)

of alarm.

ALM/MIN LED is

Amber

◆

One or more minor system alarm(s) affecting traffic have

occurred.

◆

Check the alarm filter mask to determine potential cause(s)

of alarm.

Table 14: Troubleshooting Chart

Symptom

Action

«
...
52
53
54
55
56
...
»

Summary of Contents for ECS4810-12M













































































Reviews:

No comments