Edelbrock PRO-FLO XT 3527 Page 37 User Manual Download | Manualshive

Page: 37 / 39

background image

37

Pro-Flo EFI Installation Instructions

©2008 Edelbrock Corporation

Brochure No. 63-3527

Catalog #3527, #3528
Rev. 8/08 - AJ/mc

PART NUMBERS

Edelbrock Pro-Flo

Fuel Injection System..............................................................................Edelbrock #3527, #3528
ECU power relay/Fuel pump relay .......................................................................Edelbrock #3586
Manifold Absolute Pressure sensor....................................................................Edelbrock #36019

GM 12569240

Manifold Air Temperature sensor (Push-In) .........................................................Edelbrock #3578

AC12160244

Coolant Temperature sensor .............................................................................Edelbrock #36012

GM 25036979

Throttle Position sensor ......................................................................................Edelbrock #3590
Oxygen (O

2

) sensor ...........................................................................................Edelbrock #36013

High pressure fuel pump.....................................................................................Edelbrock #3594
Fuel filter ............................................................................................................Edelbrock #3596

GM 25055065

Fuel pressure regulator.......................................................................................Edelbrock #3584

GM 17107010

Fuel injectors (set of eight)..................................................................................Edelbrock #3853
Fuel injectors (one) .............................................................................................Edelbrock #3583
Calibration Module..............................................................................................Edelbrock #3519
Calibration Module Cord/Plug..............................................................................Edelbrock #3571
Idle air control solenoid.....................................................................................Edelbrock #36015
Throttle Cable Bracket...................................................................................Edelbrock #38-0121

Many of the components of the Pro-Flo system are available separately. Many are standard OEM
parts. In the event that one of these parts need to be replaced, you are likely to find a
replacement at your local parts supplier, in addition to your local Edelbrock dealer or directly
from Edelbrock.

«
...
35
36
37
38
39
»

Summary of Contents for PRO-FLO XT 3527








































Reviews:

No comments

Related manuals for PRO-FLO XT 3527

Brand: Kathrein Pages: 7

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

Brand: GOgroove Pages: 9

Brand: ECS Electronics Pages: 16

Brand: STC Pages: 6

Brand: Rati Pages: 2

Brand: Thule Pages: 8

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: RAM Pages: 496

Brand: Opel Pages: 32

Brand: UAZ Pages: 112

Brand: Vangear Pages: 5

Brand: Safe Fleet Pages: 20

Brand: Paccar Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands