background image

 

 

Versatrax 50™ In-Line 

 

Document: UMBU014988.docm  

Revision: A04 

Created by: KJW 

Date: 20 Nov 2019 

IPN: 3080215-A04 

Source Location: C:\ePDM\ISLEng\products\bu-vt50vehicles\manuals\UMBU014988.docm

 

 

Page 9 of 25 

 

User Ma

nual

 

System Setup 

Working and Storage Environment 

The 

ICON

™ Portable Controller 

is to be used in a 

dry, covered

 environment only.  These components 

are not waterproof.  Keep all cords and cables away from water.  Read the 

ICON Portable Controller

 user 

manual for more details. 

The tether and vehicle are depth rated to 60 meters (200 feet) of water.  The tether connector and track 
connectors are dry-mate types which must be dry when making a connection.  Keep the tether connector 
capped with a dummy plug when not connected to the vehicle to help keep out dirt.  The tracks are tolerant 
to sandy and muddy conditions, although this decreases seal life.  The vehicle may also be operated in dry 
or dusty environments in the recommended operating temperature range of 0 

˚C – 50 ˚C (32 ˚F – 122 ˚F). 

The portable reel is splash resistant only.   

System storage temperatures are between -20 

˚C to 60 ˚C (-4 ˚F to 140 ˚F). 

 

ICON Portable Controller Connection 

The ICON Portable Controller supplies power to the tether and vehicle.  It provides a communication 
interface to the vehicle.  It also provides video reception and distribution. 

Refer to the Controller Setup section of the ICON Portable Controller User Manual for more information.  

 

Vehicle & Tether Connection 

It is important that the tether be properly connected to the vehicle; otherwise, damage to the system may 
result. 

1.  Connect the vehicle end of tether to the back of the harness block.  Visually line up the key in the 

connector before mating.   Fully screw down and finger-tighten the locking collar.  Do not use tools 
to tighten the IE55 collar 

– connector damage may occur if overtightened.   

 

2.  Verify the track and camera whips to their respective components are securely connected, and the 

whips are free from damage.

 

 

Mini-Reel Setup 

If your system includes a Mini-Reel, follow these steps to operate: 

1.  Remove the Mini-Reel from the shipping case. 

2.  Connect the deck cable from the reel to the Video Interface and Power Supply. 

3.  Connect the encoder deck cable from the reel to the Video Interface and Power Supply (if provided 

with Mini-Reel). 

Summary of Contents for Inuktun Versatrax 50 In-Line


























Reviews: