background image

Pretty - Nice - LADy

UK

14

clock not programmed

problem:

 

the time and date has not been set. 

the timers cannot be used.

solution:

 set the time and date and any timers in the 

respective menu.

maintenance request for cleaning

problem:

  there  are  100  operating  hours  left  from  the  time  of  the  message 

appearing before the stove will be blocked for cleaning.

solution:

 Arrange for a technician to clean the stove.

sudden power cutout

problem: 

the power has been down for more than a minute.

the stove signals the power cutout and shuts down.

alarm: gases not up to heat

problem:

 the discharge gases have become too cold; the embers have gone out.

cause:

 the pellets in the tank are finished. refill the tank.

alarm: start-up failed 

problem:

 the stove has not started up.

cause:

 

the brazier is dirty or not properly in place. No pellets. 

the element does not work. coNtAct the techNiciAN.

Vacuometer alarm

problem:

 trouble discharging the gases.

cause:

 the flue system is obstructed. coNtAct the techNiciAN.

alarm: overheating gas

problem:

 the temperature of the discharge gases has exceeded the permitted 

threshold.

cause:

 the gear motor is operating continuously, the gas probe is broken.

coNtAct the techNiciAN

alarm: stove overheating

problem:

 the body of the stove has exceeded the permitted threshold and is 

overheating.

solution:

 the fan is not cooling down the stove. coNtAct the techNiciAN.

alarm: gas evacuator motor

problem:

 the gas evacuator motor is not working or the board cannot detect 

its operation.

cause:

 the motor is not powered or the tachometer sensor is not responding. 

coNtAct the techNiciAN

annEx: aLarm and notiFication

All alarm and notification messages appear on the display, possible causes and solutions.

Summary of Contents for Lady

















Reviews: