background image

Pretty - Nice - LADy

UK

4

important inFormation rEgarding saFEtY

  PREPARATIONS FOR INSTALLATION

•  in order to prevent the possibility of fire, make sure that the apparatus is installed cor-

rectly by carefully following the instructions of this handbook.

•  Do not place the stove in rooms where curtains, carpets or other furnishings could 

burn due to the heat generated by the stove.

•  Do not position the stove near curtains, inflammable or combustible material.
•  When installing the stove, make sure that is properly connected to an earth point using 

the (green-yellow) electric cable.

•  the plug for connection to the main power supply must be accessible when the stove 

is installed.

  IMPORTANT INFORMATION 
  FOR THE USER

  Fuel used

•  this apparatus has been built to burn only 6 mm di-

ameter pellets (pressed wood). it is very important to 
choose a clean, top-quality pellet without impurities.

 

For the stove to work properly and safely it is necessary to 
use  pellets  that  comply  with  the  following  standards:  DIN 
51731 and ONORM-M 7135 (thermal value, residual humidity, diameter, quality of wood used...).

  ecowood cannot assume liability for poor operation of the stove if poor quality pellets 

are used.

•  use only pellets and 

never

 put other inflammable or combustible material in the stove.

•  Do not use the stove as an incinerator or for any purpose other than that for which it 

was intended.

•  Do not use liquid fuel.
•  keep your stock of pellets at least one metre away from the stove.

  important instructions before ignition

•  make sure that the hopper door (pellet tank) is 

closed when the stove is in operation.

•  make sure that the fireplace and ash box doors 

are properly closed.

•  before lighting the stove make sure that all mov-

ing parts have been assembled correctly in their 
respective positions.

Summary of Contents for Lady

















Reviews: