background image

Pretty - Nice - LADy

3

F

D

IT

UK

this  stove  operates  only  and  exclusively  with 
pellets (pressed wood sawdust). top quality pel-
lets without impurities should be used.
in order to obtain a constant flame with a pleas-
ing appearance it is important to use 6 mm di-
ameter pellets that are about 20 mm long, and 
as regular as possible. 

the  stove  needs  a  flue  gas  exhaust  pipe  of  80 
mm diameter and a combustion air inlet pipe of 
40 mm diameter.

Where possible, we recommend installing a t-pipe for inspection at the stove exhaust gas 
outlet, in order to recover the burnt microdust, and also a steel pipe two metres high, to 
be connected to the existing flue in order to discharge the flue gas.
this device will prevent smoke formation inside the rooms should there be a power failure 
for any reason during stove operation.

STANDARD EQUIPMENT:

•  user’s and installation handbook.
•  remote control.

OPTIONAL EQUIPMENT:

•  Wall smoke flue with quick closure.
•  external digital thermostat for the room.
•  room thermostat included in the stove.
•  Gsm telephone modem (to allow control of the stove from a remote location).

Summary of Contents for Lady

















Reviews: