Eclipse EGO User Manual Download Page 55

Page: 55 / 68

Fault Finding

Fault Finding

Symptom

Possible Cause

Solution

Eclipse Ego leaks down barrel.

Leaky Exhaust Valve.

Replace exhaust valve.

Damaged Valve Seat.

Replace Rammer Housing.

Gas vents quickly down barrel as soon
as gassed up.

The exhaust valve has become jammed
in the brass valve guide

Replace exhaust valve and brass value
guide as necessary (see Maintenance
Section).

The marker is chopping or trapping paint.

The Break Beam Sensor System is
switched off.

Switch on the Break Beam Sensor
System.

The bolt is dirty, causing the sensor
system to incorrectly detect a retracted
bolt.

Clean the bolt.

The Break Beam Sensor System is dirty
causing the incorrect detection of paintballs.

Clean the Break Beam Sensor System.

Increase the breech open time.

Incorrect seal on front of rammer housing.

Replace front seals on rammer housing
with 016 seals.

Eclipse Ego fires yet bolt doesn’t move.

Bolt pin is not located in rammer
correctly.

Lift bolt pin and line up bolt with position
of rammer correctly (see Maintenance
Section).

Fault Finding

Summary of Contents for EGO





































































Search results

Summary of Contents for EGO

Reviews:

Related manuals for EGO

Brands by name

Popular brands

Eclipse EGO, User Manual

Search results

Summary of Contents for EGO

Reviews:

Related manuals for EGO

Brands by name

Popular brands