Eclipse EGO User Manual Download Page 35

Page: 35 / 68

Advanced Set-Up

Advanced Set-Up

Scroll through the

Filter

Menu until the

RELEASE

parameter is displayed.

The current value of the trigger release time is shown
on the right hand side of the display

(See Figure 4.15)

Press the

Select

pushbutton to enter the edit function

and the edit indicators will appear on the display.

Press and release the

Raise

pushbutton to increase the

RELEASE

value in 1-millisecond increments. Press and

hold the

Raise

pushbutton to increase the

RELEASE

value

more rapidly.

Press and release the

Lower

pushbutton to decrease the

RELEASE

value in 1-millisecond increments. Press and

hold the

Lower

pushbutton to decrease the

RELEASE

value

more rapidly.

Press

Select

to save the

RELEASE

value and the edit

indicators will disappear from the display to indicate that
the value has been accepted. You have now returned to
the

Filter

Menu.

Assuming the TT filter is set correctly, the

RELEASE

parameter

can be set to 1ms for fastest trigger operation. On short
triggers this may have to be increased to prevent 'Double
Taps'.

Scroll through the

Filter

Menu until the

PULL

parameter is

displayed.

The current value of the trigger pull time is shown on
the right hand side of the display

(See Figure 4.14)

Press the

Select

pushbutton to enter the edit function

and the edit indicators will appear on the display.

Press and release the

Raise

pushbutton to increase the

PULL

value in 1-millisecond increments. Press and hold

the

Raise

pushbutton to increase the

PULL

value more

rapidly.

Press and release the

Lower

pushbutton to decrease the

PULL

value in 1-millisecond increments. Press and hold

the

Lower

pushbutton to decrease the

PULL

value more

rapidly.

Press

Select

to save the

PULL

value and the edit

indicators will disappear from the display to indicate that
the value has been accepted. You have now returned to
the

Filter

Menu.

Assuming the TT filter is correctly set, the

PULL

parameter

can be set to 0ms for fastest trigger operation.

Setting the Trigger Release Time

Setting the Trigger Pull Time

FIGURE

4.14

FIGURE

4.15

Advanced Set-Up

Summary of Contents for EGO





































































Search results

Summary of Contents for EGO

Reviews:

Related manuals for EGO

Brands by name

Popular brands

Eclipse EGO, User Manual

Search results

Summary of Contents for EGO

Reviews:

Related manuals for EGO

Brands by name

Popular brands