manualshive.com logo in svg

Eclipse CD 8445E, Owner'S Manual

Share
Download
Eclipse CD 8445E Owner'S Manual Download Page 96

„

 208 

„

Other information

MSINFO 1

YOU TRIED TO PLAYBACK 
AND READING DATA 
WHEN NO MG MEMORY 
STICK OR MEMORY STICK 
WAS INSERTED

Insert MG Memory Stick or Memory Stick.

MSINFO 2

YOU TRIED TO PLAYBACK 
AN INCORRECTLY 
FORMATTED MEMORY 
STICK

Use the deck to format the Memory Stick.

MSINFO 3

THE WRITE PROTECTION 
SWITCH IS LOCKED.

Unlock the write protection switch.

MSINFO 4

THE MEMORY STICK FULL Delete some of the data from the Memory Stick 

before saving.

MSINFO 5

YOU TRIED TO RECORD 
MORE THAN THE 
MAXIMUM NUMBER OF 
TRACKS (400) ONTO A MG 
MEMORY STICK

Delete some of the MG Memory Stick data or use 
a different MG Memory Stick for recording.

MSINFO 6

AN INCOMPATIBLE 
MEMORY STICK HAS 
BEEN INSERTED

Check that the Memory Stick can be used with 
this deck.

MSINFO 7

MG MEMORY STICK 
CONTAINING NO MUSIC 
DATA HAS BEEN 
INSERTED

Insert a MG Memory Stick containing music data. 

MSINFO 8

YOU TRIED TO PLAYBACK 
DATA THAT INCLUDES A 
PLAYBACK GUARD

Data that includes a playback guard can not be 
played back.

MSINFO 9

MG MEMORY STICK YOU 
TRIED TO PLAY BACK HAS 
PLAYBACK LIMITATIONS

Data that includes a playback guard can not be 
played back.

FILE ERR

A MG MEMORY STICK 
CONTAINING 
INCOMPATIBLE FILES HAS 
BEEN INSERTED

Insert a MG Memory Stick containing compatible 
files.

LOAD_MAP_D
ATA

DAMAGE TO MEMORY 
STICK DATA

Memory stick data is damaged because the 
ignition switch has been turned ON/OFF during 
the data import process.

SIZE_ERR

THE VOLUME OF IMPORT 
DATA IS LARGE

Confirm the Memory Stick data.

Summary of Contents for CD 8445E






































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands