Eclipse CD 8445E Owner'S Manual Download Page 33

Page: 33 / 101

How to operate the Memory Stick player

145

Turn to the right:

Advances to the next track.

Turn to the left:

Returns to the beginning of the
track being played. (Repeat turning
for previous tracks.)

Fast forward or rewind the song
currently being played.

[ ]

button:

Fast forward.

[ ]

button:

Rewind.

Pressing the button causes the
player to move up to the next track
and play it for 10 seconds, then
move up to the next track and play it
for 10 seconds, and so on until the
button is pressed again.

ATTENTION

• To continue playing a desired

track, press the button again to
stop scanning.

• After the entire disc is scanned

once, ordinary playback starts
from the point where scanning
started.

To cancel, press the [5 RPT] button
again.

Advancing to the next track
or returning to the beginning
of the track being played

Turn the [SEL] button to the left or
right.

Fast Forward/Rewind

Press and hold the [

] or

[

]button.

Playing the beginning of
tracks (SCAN)

Press the [4 SCAN] button.

Repeating the same track
(REPEAT)

Press the [5 RPT] button to repeat
the track being played.

Summary of Contents for CD 8445E






































































































Search results

Summary of Contents for CD 8445E

Reviews:

Related manuals for CD 8445E

Brands by name

Popular brands

Eclipse CD 8445E, Owner'S Manual

Search results

Summary of Contents for CD 8445E

Reviews:

Related manuals for CD 8445E

Brands by name

Popular brands