manualshive.com logo in svg

Eclipse CD 8445E, Owner'S Manual

Share
Download
Eclipse CD 8445E Owner'S Manual Download Page 9

Table of Contents

„

 121 

„

How to operate the ACC security ............................................................................... 168
How to turn the security indicator on/off ..................................................................... 168
How to read the Electronic Serial Number ................................................................. 168

Detaching the front panel.................................................................. 169

Using the detachable panel ........................................................................................ 169

How to remove the detachable panel................................................................... 169
How to fit the detachable panel............................................................................ 169

How to operate the AUDIO CONTROL ............................................. 170

Adjusting audio volume .............................................................................................. 170
Enabling the loudness control .................................................................................... 170
Switching audio control modes................................................................................... 171

How to operate the Sound Adjustment Mode ................................. 173

About Sound Adjustment Mode.................................................................................. 173

SRS Circle Surround II (CS II) ............................................................................. 173
Parametric equaliser ............................................................................................ 174
Time Alignment .................................................................................................... 175
Crossover............................................................................................................. 175
Multi-harmonizer .................................................................................................. 177
Non-Fader phase ................................................................................................. 177
Non-Fader output ................................................................................................. 177
Selecting the speaker layout ................................................................................ 177
Sound effect customisations ................................................................................ 177

Operations during Normal Mode ................................................................................ 178

SRS Circle Surround II (CS II) ............................................................................. 178
Parametric equaliser adjustment (PEQ)............................................................... 179
Selecting an equaliser mode from memory.......................................................... 180
Measuring/display frequency characteristic ......................................................... 180
Time alignment settings (Time Alignment)........................................................... 181
Crossover adjustment (X-Over) ........................................................................... 184
Multi-harmonizer settings (Harmonizer) ............................................................... 184
Non-Fader phase selection (Non-F Phase) ......................................................... 185
Non-Fader Output ................................................................................................ 185
Importing Sound Data .......................................................................................... 185

Operations during Pro Mode ...................................................................................... 186

Summary of Contents for CD 8445E






































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands