manualshive.com logo in svg

Eclipse Combustion Vortometric v2.00, Installation Manual, Page: 23 / 51

Share
Download
Eclipse Combustion Vortometric v2.00 Installation Manual Download Page 23

Figure 3.3

  Vortometric Burner Mounting Arrangements

3-13

Provide adequate

shell stiffeners

Furnace backstay

Weld heads of mounting bolts inside furnace shell plate.
Allow for 3mm (1/8") thick, high temperature gasket
between the burner flange and shell plate.

Furnace shell plate

229mm (9")*
Flange position on standard burner allows correct shell dimension above
*178mm (7") for 6V and 8V medium intensity burner sizes.  

To allow for thermal expansion of combustion liner extension,
the main wall should be constructed with an opening 25mm (1") greater
in diameter than diameter of combustion liner. 
The outside of combustion liner should be covered with 1/8" thick
insulating paper. The remaining gap between the burner and main wall
should be densely packed with ceramic fiber or wool blanket insulation.

3mm (1/8") high temp. gasket

(Customer supplied)

Ring

90  hold

Smooth refractory
flush with throat

Main flame

scanner

152mm (6")

minimum

for standard

burner mounting

76mm (3")

maximum

projection

Burner mounting
box by customer

229mm to 457mm

(9" to 18")

229mm (9") minimum

Cup angle or special anchor
fitting welded to shell plate

1

2

3

4

5

6

7

Furnace Backstay 

Furnace Shell Plate

Block Insulation

Insulated Fire Brick

Fire Brick

Castable Refractory Ring (Alternate Plastic)

Refractory  or Alloy Anchor
(305mm to 457mm or 12" to 18" apart)

5

6

7

4

3

1

2

Alternate Mounting Arrangement

For Thin Walls

Alternate Mounting Arrangement

For Thick Walls

Suggested Mounting Arrangement

For Standard Burner

General Notes:

1. Mounting illustrations show typical Vortometric combustor blocks of high alumina

plastic refractory as used by Eclipse for normal duty. 

2. The dimensions given must be held as specified, and the inner diameter of the

combustor must be round and concentric with the throat cone.

3. Alloy rod-type anchors welded inside the combustor block are the customer’s

responsibility if the refractory is field installed rather than factory installed.

4. All mounting arrangements are meant for vertically or horizontally fired burners.

Regardless of orientation, the refractory block MUST be protected from thermal
expansion of the furnace wall.

30 

Eclipse Vortometric Burner v2.00, Installation Guide 248, 4/10/07

Summary of Contents for Vortometric v2.00




















































Reviews:

No comments