Echometer M Manual Download Page 2

Page: 2 / 45

Echometer Company

Model – M Manual

Phone: (940) 767-4334

5001 Ditto Lane

Page

Fax: (940) 723-7507

Wichita Falls, Texas 76302, U.S.A.

E-Mail:Table of Contents

Introduction ............................................................................................................................................... 1

Limits of Liability .............................................................................................................................. 1
Copyright Notice ................................................................................................................................ 1
Trademarks ......................................................................................................................................... 1

Table of Contents ...................................................................................................................................... 2
1 - Safety Considerations .......................................................................................................................... 4

Echometer Schools ............................................................................................................................. 4
Additional Information....................................................................................................................... 4

2-Principles of Acoustic Measurements ................................................................................................... 5

Recording and Interpretation of Signals ............................................................................................. 5
Depth Calculation .............................................................................................................................. 6

3 – General Description – Model M ......................................................................................................... 7

Instrument Panel .................................................................................................................................... 8

Wellhead Attachments .............................................................................................................................. 9

Remote Fire Gas Gun ....................................................................................................................... 11
High Pressure Gas Guns................................................................................................................... 12

Accessories .......................................................................................................................................... 12

Model M Modifications and Enhancements…………………………………………………………13
4 - Operation ........................................................................................................................................... 15

5 - Interpretation ..................................................................................................................................... 20
6 - Problem Wells ................................................................................................................................... 21
7 - Battery and External Power Information ........................................................................................... 22

Important Notes and Instructions for Rechargeable Batteries .......................................................... 23

8 - Testing/Troubleshooting.................................................................................................................... 24

9 - Maintenance ...................................................................................................................................... 25

Compact Gas Gun Pressure Rating .................................................................................................. 25
Compact Gas Gun Disassembly and Assembly Special Precautions ............................................... 25
Remote Fire Gas Gun Pressure Rating ............................................................................................. 26
Remote Fire Gas Gun Disassembly and Assembly Special Precautions ......................................... 26

Summary of Contents for M














































Search results

Summary of Contents for M

Reviews:

Echometer M, Manual, Page: 2 / 45

Search results

Summary of Contents for M

Reviews: