manualshive.com logo in svg

Echometer M, Manual, Page: 12 / 45

Share
Download
Echometer M Manual Download Page 12

Echometer Company 

 Model – M Manual 

Phone:  (940) 767-4334 

5001 Ditto Lane 

Page 

12

 

Fax: (940) 723-7507 

Wichita Falls, Texas  76302, U.S.A. 

 

E-Mail: 

Casing Pressure Gauge or Optional Transducer 

The casing pressure and casing pressure buildup during the acoustic test must be measured with an accurate and sensitive 
pressure gauge or sensor.  The Remote Fire Gas Gun supplied with the Echometer Model M is equipped with a quick 
connect gauge that covers the range 0-200 psig.  The user should consider the option of obtaining several gauges 
covering different pressure ranges. 

 

Charging the Gas Volume Chamber

 

To charge the volume chamber, first connect the filler adapter to a 7.5 oz. CO

2

 bottle.  Then, press the adapter against 

the filler fitting on the gun.  When these two fittings are pressed together, a valve core in the bottle is depressed and gas 
will flow from the bottle into the volume chamber.  Charge the chamber to at least 100 PSI above casing pressure before 
attaching the gas gun to the casing annulus valve to prevent debris from entering the gas gun internal valve parts.  The 
volume chamber pressure can be read on the gun-mounted gauge.  A 5-LB, CO

2

 bottle and hose with connector can be 

used to change the gun, if desired.   
 

 
High Pressure Gas Guns 

 
The 5000-psi gas gun is normally used in the implosion mode. It has an excellent noise-canceling microphone and 
generates a very good pulse when the 

1

/

2

-inch ball valve is opened rapidly and the well pressure exceeds 200-psi. When 

the 5000-psi gas gun becomes dirty due to debris imploding from the wellbore, the volume chamber and the microphone 
assembly can be easily flushed with a solvent.  The 5000-psi gas gun requires very little maintenance.  It is excellent for 
gas lift, flowing and high-pressure shut-in wells.  It can be used in the explosion mode by charging the gas gun volume 
chamber to a pressure in excess of the well pressure. 
 
The 15000-psi High Pressure Gas Gun operates in the implosion mode only. Excellent results have been obtained at 
pressures above 1500-psi through needle valves with 1/8-inch orifices, which are standard in most high-pressure wells.   
 
For more details please refer to the Gun-Microphone Assemblies brochure in the appendix. 

 

Accessories 

      Battery Charger (110 V- AC) or (220 V - AC if requested) 
      Automobile Battery Cable 
      Automobile Cigarette Lighter Cable 
      Casing Pressure Gauges 
 

Precision Test Gauge 

 

Precision Digital Gauge 

      Gas Cylinders 
 

2-1/2 LB CO

2

 

 

5 LB CO

2

 

 

Nitrogen Cylinder 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for M














































Reviews:

No comments