EchoMaster Pro FCTP-MB1903 Installation Manual Download Page 15 | Manualshive

Page: 15 / 22

background image

15

Installation Guide

15

tel - 1-800-477-2267

email - [email protected]

Illustrations are typical and may not match exact vehicle detail

Step 3

Remove the three Torx T30 screws holding the
mirror to the door of the truck.

One of the Torx T30 screws has a small cap
covering it. Use something slim to pry the cover
off to access the screw.

The mirror arm will still be held on with a clip on
the outside.

Step 4

Using a nylon pry tool, insert it (approximately as
shown - above the hook) then pull it out and push
the mirror assembly up to disengage.

Step 5

Feed a long wire tie or similar fish tool through the door
to where the factory wires come through the boot.

FCTP-MB1903

Sprinter Tow Package

«
...
13
14
15
16
17
...
»

Summary of Contents for FCTP-MB1903























Reviews:

No comments

Related manuals for FCTP-MB1903

Brand: D-2 Incorporated Pages: 28

Brand: D+H Pages: 12

Brand: Darfon Pages: 28

Brand: VanEssa mobilcamping Pages: 8

Brand: Ecco Pages: 9

Brand: Ecco Pages: 9

Brand: TATA Motors Pages: 164

Brand: Gardener's Pages: 2

Brand: GCE Pages: 16

Brand: GCC Technologies Pages: 12

Brand: Keis Pages: 2

Brand: Darimo Pages: 2

Brand: Waldbeck Pages: 7

Aerasgard KCO2-W

Brand: S+S Regeltechnik Pages: 16

Brand: Honda Pages: 73

Brand: Cequent Pages: 9

Brand: Quantum Pages: 3

Brand: SICK Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands