EchoMaster Pro FCTP-MB1903 Installation Manual Download Page 18 | Manualshive

Page: 18 / 22

background image

18

Installation Guide

18

tel - 1-800-477-2267
email - [email protected]

Illustrations are typical and may not match exact vehicle detail

FCTP-MB1903

Sprinter Tow Package

Step 5

When installing the camera insert on to the mirror
caps, the locating tab will line up with a small hole
on the front of the camera insert.

Step 6

Once the camera insert is installed in place,
use a number 1 Phillips screwdriver to mount
the camera insert.

Step 7

Once the camera insert is installed, snap the turn
signal in place. Reinstall the mirror caps, in the
reverse order they were removed.

Make sure all connections in the mirror are fully
seated and secure when reinstalling everything.

NOTE

DO NOT OVER TIGHTEN

Mirror Assembly (continued)

«
...
16
17
18
19
20
...
»

Summary of Contents for FCTP-MB1903























Reviews:

No comments

Related manuals for FCTP-MB1903

Brand: Samsung Pages: 133

Brand: Lamtec Pages: 18

Brand: Ladybug Pages: 33

Brand: Quintex Pages: 29

Brand: Oki Pages: 4

Brand: RAM Commercial Pages: 12

Brand: Pitney Bowes Pages: 22

Brand: Alpine Pages: 2

Brand: Whispbar Pages: 15

Brand: Varec Pages: 70

Brand: Adam Pages: 22

Brand: BS Bodensteckdosen Systemtechnik Pages: 14

Brand: hepco & becker Pages: 6

Brand: Groov-e Pages: 2

Brand: TrailFX Pages: 6

Brand: BESAFE Pages: 4

Brand: Transcend Pages: 64

Brand: MELINERA Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands