manualshive.com logo in svg

Echo PB-755S H, Operator'S Manual

Share
Download
Echo PB-755S H Operator'S Manual Download Page 30

MAINTENANCE

PB-755S H/T

30

X7531122809

© 5/2016 ECHO Inc.

Overheating and engine seizure can 
occur when:

• Air intakes are blocked, preventing 

cooling air from reaching the 
cylinder.

• Dust and grass build up on the 

outside of the cylinder. This build 
up insulates the engine and 
prevents the heat from leaving.

Removal of cooling passage 
blockages or cleaning of cooling fins is considered “Normal Maintenance.” Any 
failure attributed to lack of maintenance is not warranted.

Cleaning Grill

1.

Brush accumulated debris from intake grill between backpack frame and 
blower housing.

Cleaning Cylinder Fins

1.

Disconnect spark plug lead from 
spark plug, and remove engine 
cover.

2.

Clean cylinder fins (A) to allow 
cooling air to pass freely.

3.

Install engine cover and attach 
spark plug lead. 

Exhaust System

Spark Arrestor Screen

Level 2.

Carbon deposits in muffler will cause a drop in engine output and 
overheating. Spark arrestor screen must be checked periodically.

Parts Required:

Spark Arrestor Screen, Gasket

A

Summary of Contents for PB-755S H













































Reviews:

No comments

Brands by name

Popular brands

Load more brands