manualshive.com logo in svg

Echo PB-755S H, Operator'S Manual

Share
Download
Echo PB-755S H Operator'S Manual Download Page 22

OPERATION

PB-755S H/T

22

X7531122809

© 5/2016 ECHO Inc.

Storage

 - Fuel storage laws vary by locality. Contact your local government for 

the laws affecting your area. As a precaution, store fuel in an approved, airtight 
container. Store in a well-ventilated, unoccupied building, away from sparks and 
flames.

Stored fuel ages. Do not mix more fuel than you expect to use in thirty 
(30) days, ninety (90) days when a fuel stabilizer is added.

Stored two-stroke fuel may separate. ALWAYS shake fuel container 
thoroughly before each use.

Starting Cold Engine

• Recoil starter: Use short pulls - only 1/2-2/3 of rope length for starting. Do not 

allow the rope to snap back in. Always hold the unit firmly.

- PB-755S H 

1.

Throttle Lever

Move throttle position lever (A) to 
IDLE DETENT position.

- PB-755S T 

1.

Throttle Position / Stop Switch 
Button

Move throttle position lever (A) 
forward to IDLE position. Slide 
stop switch (B) forward to RUN 
position.

PB-755S H

A

PB-755S T

B

A

Summary of Contents for PB-755S H













































Reviews:

No comments

Brands by name

Popular brands

Load more brands