background image

X7531122809

9

© 5/2016 ECHO Inc.

PB-755S H/T

SAFETY

Repetitive Stress Injuries (RSI)

It is believed that overusing the muscles and 
tendons of the fingers, hands, arms, and 
shoulders may cause soreness, swelling, 
numbness, weakness, and extreme pain in 
those areas. Certain repetitive hand activities 
may put you at a high risk for developing a 
Repetitive Stress Injury (RSI). An extreme RSI 
condition is Carpal Tunnel Syndrome (CTS), 
which could occur when your wrist swells and 
squeezes a vital nerve that runs through the 
area. Some believe that prolonged exposure to 
vibration may contribute to CTS. CTS can cause 
severe pain for months or even years.

To reduce the risk of RSI/CTS, do the following: 

• Avoid using your wrist in a bent, extended, or twisted position. Instead try to 

maintain a straight wrist position. Also, when grasping, use your whole hand, 
not just the thumb and index finger.

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitive movement.

• Do exercises to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doctor if you feel 

tingling, numbness, or pain in the fingers, hands, wrists, or arms. The sooner 
RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage 
can be prevented.

All over head electrical conductors and communications wires can 
have electricity flow with high voltages. This unit is not insulated 
against electrical current. Never touch wires directly or indirectly, 
otherwise serious injury or death may result.

Do not operate this product indoors or in inadequately ventilated 
areas. Engine exhaust contains poisonous emissions and can 
cause serious injury or death.

Summary of Contents for PB-755S H













































Reviews: