manualshive.com logo in svg

Echo PB-755S H, Operator'S Manual

Share
Download
Echo PB-755S H Operator'S Manual Download Page 25

X7531122809

25

© 5/2016 ECHO Inc.

PB-755S H/T

OPERATION

Operating Blower

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a 
poison gas. Breathing CO can cause unconsciousness, serious 
injury, or death. Exhaust can cause serious burns. ALWAYS 
position unit so that exhaust is directed away from your face and 
body.

Always wear safety glasses, hearing protection and a face filter 
mask or serious personal injury may result. Do not point the blower 
pipe in the direction of people or pets. 

Use reduced speed only when performing light-duty tasks or to comply 
with local noise regulations. Continuous low speed operation may allow 
fuel/oil residue to build-up on the piston and cause rapid build-up of 
carbon on the spark arrestor screen, resulting in overheating and engine 
damage. To reduce harmful build-up, run engine at wide open throttle for 
at least 5 minutes every hour, and inspect/clean the spark arrestor 
screen after approximately 40 hours of operation. 

Read the Safety Section carefully.

To avoid engine damage due to over-revving, do not block blower pipe.

1.

Use only during appropriate hours.

2.

Allow the engine to warm up at a fast idle for a few minutes.

3.

PB-755S H

Set engine speed with throttle 
lever (A).

PB-755S H

A

Summary of Contents for PB-755S H













































Reviews:

No comments

Brands by name

Popular brands

Load more brands