manualshive.com logo in svg

Echo PB-755S H, Operator'S Manual

Share
Download
Echo PB-755S H Operator'S Manual Download Page 27

X7531122809

27

© 5/2016 ECHO Inc.

PB-755S H/T

MAINTENANCE

ECHO offers 

REPOWER

TM

 Maintenance Kits and Parts to make your 

maintenance job easier.

Maintenance Intervals

IMPORTANT NOTE

 - Time intervals shown are maximum. Actual use and your 

experience will determine the frequency of required maintenance.

MAINTENANCE PROCEDURE NOTES:

(1) Low evaporative fuel tanks DO NOT require regular maintenance to maintain 
emission integrity.

* Replacement is recommended based on the finding of damage or wear during 
inspection

COMPONENT/SYSTEM

MAINTENANCE 

PROCEDURE

REQ’D 

SKILL 

LEVEL

Daily or Before Use

Air Filter 

Inspect/Clean*

1

Choke Shutter 

Inspect/Clean *

1

Fuel System 

Inspect (1)

1

Cooling System 

Inspect/Clean 

2

Recoil Starter Rope 

Inspect/Clean*

1

Screws/Nuts/Bolts Inspect/Tighten/Replace* 

1

Every Refuel

Fuel System 

Inspect (1)

1

3 Months

Air Filter 

Replace*

1

Fuel Filter 

Inspect*

1

Fuel Cap Gasket 

Inspect*

1

Spark Plug 

Inspect/Clean/Replace*

1

Muffler Spark Arrestor 

Inspect/Clean/Replace* 

2

Cylinder Exhaust Port 

Inspect/Clean/Decarbon 

2

Yearly

Fuel Filter 

Inspect/Replace*

1

Fuel Cap Gasket 

Replace* 

1

Summary of Contents for PB-755S H













































Reviews:

No comments

Brands by name

Popular brands

Load more brands